Skip to content
Omnikalc

Piezo stack actuator calculator

Enter the number of layers, the d33 coefficient, the voltage and the stiffness to get the free stroke, the blocking force and the field in each layer.

Updated on
Your inputs

Value out of range

pm/V

Value out of range

V

Value out of range

mil

Value out of range

lbf/mil

Value out of range

Results

Free stroke

0.472 mil

Blocking force

134.6 lbf

Electric field in each layer
25.00 V/mil
Active length of the stack
0.80 in
Strain (stroke ÷ length)
0.059 %
Field class (0 safe, 1 high, 2 over the usual limit of 2 kV/mm)
0

The piezo stack actuator calculator gives the free stroke, the blocking force, the electric field in each layer, the active length, the strain and a field class, from the number of layers, d33, the voltage, the layer thickness and the stiffness.

How the calculation works

  • Enter the number of layers, the d33 coefficient and the drive voltage.
  • Enter the thickness of one layer to check the electric field.
  • Enter the stiffness of the stack to get the blocking force.

Example

A stack of 200 layers of 4 mil with a d33 of 600 pm/V driven at 100 V has a free stroke of 0.472 mil over an active length of 0.80 in, a strain of 0.059 %. With a stiffness of 285 lbf/mil, the blocking force is 134.6 lbf. The field in each layer is 25.00 V/mil, class 0.

Why it matters

The calculator helps mechatronics and precision engineering students and designers who size piezo actuators for nanopositioning, valves, inkjet heads, active vibration control or adaptive optics, and who need to compare the stroke and force of a stack with the requirement of the application.

Good to know

Use the d33 of the ceramic at the operating field, since the effective value is often higher at large signal than the small-signal datasheet figure. The stiffness is given in the datasheet of the stack and includes the end caps. The calculation ignores hysteresis, creep, the temperature and the compliance of the load, and the stroke is for an unloaded actuator. Stay below the rated voltage and avoid a negative field unless the datasheet allows it. Piezoelectric actuators also need a driver able to supply the peak current of the capacitive load.

The linear actuator force calculator covers motor-driven actuators, the capacitors calculator helps with the electrical load of the stack, the Hooke’s law calculator relates force and displacement and the compression spring calculator handles a spring preload.

Frequently asked questions

How is the stroke of a piezo stack computed?

Each layer expands by d33 times the voltage across it, and the layers are connected electrically in parallel and mechanically in series. The free stroke is therefore ΔL = n × d33 × V, which is proportional to the number of layers and to the voltage. A layer of PZT with d33 of 600 pm/V expands by 0.06 µm at 100 V.

What is the blocking force?

The blocking force is the force needed to prevent the stack from moving at all, at full voltage. It equals the stiffness of the stack times the free stroke, F = k × ΔL. In practice, the force available decreases linearly to zero as the stack extends to its free stroke against a spring.

What limits the drive voltage?

The field in each layer, E = V / t, must stay below the depolarization and breakdown limits, typically 1 to 2 kV/mm for PZT, and the negative field must be limited, since it can depolarize the ceramic. Thinner layers allow a lower voltage for the same field, which is why multilayer stacks use layers of 50 to 150 µm.

Why is the real stroke less?

Real stacks have inactive end caps, adhesives and a load that opposes the motion. Hysteresis of the ceramic, a few percent to 15 percent, also makes the stroke differ between rising and falling voltages. Datasheets give the free stroke at the rated voltage, which is the figure to compare with the calculation.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.