Skip to content
Omnikalc

Poisson's ratio calculator: how much does a material narrow when stretched?

Enter the length and width of a sample before and after stretching, and the Young's modulus, to get the axial and lateral strain, Poisson's ratio, the shear modulus and the bulk modulus.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

mm

Value out of range

mm

Value out of range

GPa

Value out of range

Results

Poisson's ratio (ν)

0.320

Within the usual range of 0 to 0.5

Shear modulus (G)

75.8 GPa

Axial strain
0.500%
Lateral strain
-0.160%
Bulk modulus (K)
185.2 GPa

Stretch a rubber band and it gets thinner. Poisson’s ratio measures by how much. This Poisson’s ratio calculator takes the length and width of a sample before and after being stretched, plus the Young’s modulus, to give the axial strain, the lateral strain, Poisson’s ratio, the shear modulus and the bulk modulus.

How the calculation works

  • Axial strain = change in length ÷ original length.
  • Lateral strain = change in width ÷ original width.
  • Poisson’s ratio ν = −lateral strain ÷ axial strain. The minus sign makes it positive for a material that narrows when stretched.
  • Shear modulus G = E ÷ [2(1 + ν)] and bulk modulus K = E ÷ [3(1 − 2ν)], from the Young’s modulus E.

Example

A steel rod of original length 100 mm and diameter 10 mm is stretched by 0.5 mm, and its diameter shrinks by 0.016 mm. The axial strain is 0.5 % and the lateral strain is −0.16 %, so ν = 0.0016 ÷ 0.005 = 0.32. With E = 200 GPa, the shear modulus is 75.8 GPa and the bulk modulus 185.2 GPa.

Why it matters

Engineers need Poisson’s ratio to predict how parts deform in more than one direction, to convert between elastic moduli and to run stress analysis. In a material test lab, measuring the width change during a tensile test gives the ratio, and from it the other constants of the material.

Good to know

The relationships between E, G, K and ν are valid for linear elastic, isotropic materials, so they do not apply to wood, composites or single crystals, which have different values in different directions. Measure the strains in the elastic range, before yielding, because beyond it the ratio approaches 0.5 for metals. The lateral change is small, and a poor measurement of 0.001 mm changes the answer a lot, so use a strain gauge or an extensometer. Use consistent units for length and width changes.

The Young’s modulus calculator relates stress to strain, the section modulus calculator is used in beam design and the strain gauge calculator converts a gauge reading to strain.

Frequently asked questions

What is Poisson's ratio?

It is the ratio of the lateral contraction to the axial extension of a material under tension. Most materials narrow when stretched, so the ratio is positive.

What are typical values?

Steel is about 0.27 to 0.30, aluminum 0.33, copper 0.34, rubber close to 0.5, glass 0.2 to 0.25, concrete 0.1 to 0.2 and cork near 0. The theoretical limits for an isotropic material are −1 and 0.5.

What does a ratio of 0.5 mean?

The material keeps its volume when stretched. Rubber and other soft materials are nearly incompressible and come very close to 0.5.

Can the ratio be negative?

Yes. Auxetic materials, such as certain foams and structures, get wider when stretched. They are used in sports gear, filters and impact-absorbing parts.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.