Skip to content
Omnikalc

Recrystallization calculator: how much solvent to use and how much pure compound you recover

Enter the mass and purity of the crude solid and its solubility in the hot and cold solvent to get the solvent volume, the compound lost in the mother liquor and the recovery.

Updated on
Your inputs
g

Value out of range

%

Value out of range

g/100 mL

Value out of range

g/100 mL

Value out of range

%

Value out of range

Results

Pure compound recovered

4.00 g

Recovery of the pure compound

89.0%

Good recovery Most of the pure compound crystallizes.
Minimum volume of hot solvent
22.5 mL
Volume of solvent used
24.8 mL
Lost in the cold mother liquor
0.50 g
Recovery with exactly the minimum volume
90.0%
Impurities in the crude solid
0.50 g

Recrystallization purifies a solid by dissolving it in a minimum of hot solvent and letting it crystallize on cooling: the compound you want comes out of solution while the impurities stay dissolved. The method works because the compound is much more soluble hot than cold. This calculator estimates the minimum volume of solvent, the amount of compound you lose in the mother liquor and the recovery you can expect.

How the calculation works

  • Pure compound in the crude = mass × purity
  • Minimum solvent = pure compound ÷ hot solubility × 100 (in mL, with solubility in g per 100 mL)
  • Solvent used = minimum × (1 + excess)
  • Lost in the cold solvent = cold solubility × solvent used ÷ 100, but never more than the pure compound
  • Recovery = (pure compound − loss) ÷ pure compound

Example

You have 5 g of a solid that is 90 % pure, so it holds 4.5 g of the compound and 0.50 g of impurities. The solvent dissolves 20 g per 100 mL hot and 2 g per 100 mL cold. The minimum volume is 22.5 mL; with a 10 % excess you use 24.8 mL. The cold solvent keeps 0.50 g in solution, so you recover 4.00 g of pure compound, which is 89.0 %. With exactly the minimum volume the recovery would be 90.0 %.

Why it matters

A good solvent shows a large difference between hot and cold solubility. If the ratio is only 2 or 3, much of the compound stays in solution and the yield is low. Too much solvent is the most common mistake: each extra millilitre keeps more compound dissolved. The calculator shows how much a 10 or 50 percent excess costs.

Good to know

The model assumes that the impurities stay dissolved in the cold solvent and that the compound’s solubility is not changed by them, which is true if impurities are few. It also assumes that crystallization reaches the equilibrium solubility, which needs slow cooling and time. A second crop can be recovered by concentrating the mother liquor, but it is usually less pure. Solubility values must be for the same solvent and temperatures as in your lab; use a handbook or a quick test tube trial. Seeds or scratching the flask can start crystallization.

In practice

Weigh the crude, dissolve it in the smallest amount of boiling solvent, filter hot if there are insoluble particles, then cool slowly and finish in an ice bath. Compare the actual recovery with the prediction: a big gap points to losses on the glassware or a solvent that kept more than expected.

Frequently asked questions

How much solvent should I use for recrystallization?

Use the minimum volume that just dissolves the solid at the boiling point, plus a small excess of about 5 to 10 percent. Too much solvent lowers the yield.

What is a good recovery in recrystallization?

A recovery of 70 to 90 percent is common. Below 50 percent suggests a poorly chosen solvent or too much solvent.

Why can I never recover 100 percent?

Some compound always stays dissolved in the cold solvent, equal to its cold solubility times the solvent volume.

Does the calculator remove the impurities?

It assumes the impurities stay dissolved. If an impurity is as insoluble as your compound, it will co-crystallize and you need another solvent.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.