Skip to content
Omnikalc

Triac phase-angle dimmer calculator

Enter the firing angle, the mains voltage and frequency and the lamp power to get the output voltage, the power and the delay after the zero crossing.

Updated on
Your inputs
°

Value out of range

V

Value out of range

Hz

Value out of range

W

Value out of range

Results

Power in the load

50.0 W

Output voltage (rms)
84.9 V
Share of full power
50.0 %
Delay after the zero crossing
4.17 ms
Conduction angle
90 °
Load current (rms)
0.589 A
Input power factor
0.707

The triac dimmer calculator gives the output voltage, the power in the load, the share of full power, the delay after the zero crossing, the conduction angle, the load current and the power factor of a phase-angle dimmer.

How the calculation works

  • Enter the firing angle of the triac, between 0 and 180 degrees.
  • Enter the mains voltage, the frequency and the power of the load at full brightness.
  • The calculator finds the share of the wave that reaches the load, then the rms voltage, the power, the delay in milliseconds and the power factor.

Example

A triac fired at 90 ° on 120 V delivers 84.9 V to a resistive load of 100 W, which is 50.0 % of the full power, or 50.0 W. The firing comes 4.17 ms after each zero crossing, the triac conducts over 90 °, the load current is 0.589 A and the power factor at the input is 0.707.

Why it matters

The calculator helps electricians, hobbyists and designers who build or check light dimmers, heater controls and small motor speed controllers, and students who learn how phase control cuts the wave.

Good to know

Power is not proportional to the firing angle: the power falls slowly at first and quickly near 180 degrees, and half power is at exactly 90 degrees. The dimmer must be rated for the load, with a minimum load as well as a maximum, and derated when several dimmers are in one box because of heat. Phase-angle control adds harmonics and electromagnetic noise, so a choke and a snubber are common. For LED lamps use a compatible trailing-edge dimmer or a PWM controller. All mains work must follow the local electrical code, and a mains dimmer must be installed in a proper enclosure by a qualified person.

The RMS voltage calculator gives the rms value of a wave, the power factor correction calculator sizes the compensation of a load, the PWM duty cycle calculator handles low-voltage dimming and the Ohm’s law calculator gives the current of a resistive load.

Frequently asked questions

How does a triac dimmer work?

A triac is fired late in each half-cycle of the mains, at a firing angle α after the zero crossing, and then conducts until the next zero crossing. The load sees the part of the wave from α to 180 degrees. A late firing angle cuts more of the wave and lowers the rms voltage and the power, so the lamp is dimmer.

What is the formula for the power?

For a resistive load the power is a fraction P / P0 = 1 − α / π + sin(2 × α) / (2 × π) of the full power, with α in radians. At 90 degrees the fraction is exactly one half, at 60 degrees it is about 0.805 and at 120 degrees about 0.195. The rms voltage is the mains voltage times the square root of the fraction.

Why is the power factor lower than 1?

The current is zero during the delay and then jumps to a value set by the voltage, so it is not a sine wave and it lags the voltage in effect. For a resistive load the power factor is the square root of the power fraction, 0.71 at half power. The distortion also creates harmonics and radio noise that a small LC filter in the dimmer reduces.

Does this work for every lamp?

The formulas are for a resistive load such as an incandescent or halogen lamp. LED lamps and inductive loads behave differently: a LED driver needs a dimmer designed for it, and an inductive load makes the current lag, which can stop the triac from turning off cleanly. Use the dimmer rating on the label and a trailing-edge model for electronic loads.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.