Skip to content
Omnikalc

Wind shear calculator: how fast is the wind at a higher height?

Enter the wind speed and height of the measurement, the target height and the terrain to get the wind speed and power density at the target height.

Updated on
Your inputs
mph

Value out of range

ft

Value out of range

ft

Value out of range

Results

Wind speed at the target height

14.01 mph

Speed ratio between the two heights
1.168
Wind power density at the reference height
94.6 W/m²
Wind power density at the target height
150.6 W/m²
Gain in available wind power
59.3 %

Wind is slower near the ground and faster higher up, and the difference matters for turbines, sails, kites and buildings. The wind shear power law calculator takes the wind speed and height of a measurement, the target height and the terrain, and gives the wind speed at the target height, the speed ratio, the power density at both heights and the gain in available power.

How the calculation works

  • Enter the wind speed you measured and the height of the instrument. Standard anemometers sit at 33 ft (10 m).
  • Enter the target height, such as the hub of a small turbine or the height of a roof.
  • Pick the terrain, which sets the shear exponent α. Smooth surfaces like water have a small α, and rough ones like forests and towns have a large one.
  • The wind speed follows the power law v₂ = v₁ × (h₂ ÷ h₁)^α. The power in the wind grows with the cube of the speed, so a small gain in speed gives a bigger gain in available power.

Example

An anemometer at 33 ft reads 12 mph over open flat ground, where α is about 0.14. At a hub height of 100 ft, the ratio is (100 ÷ 33)^0.14 = 1.168, so the wind reaches 14.0 mph. The available power density rises from 94.6 W/m² to 150.6 W/m², a gain of 59.3 %. In a suburb with α near 0.25, the gain in speed is bigger, but the wind at the lower height is also much slower.

Why it matters

Most anemometers sit at 10 m (33 ft), but turbines, masts and rooftops are higher. Extrapolating the wind speed with the power law gives a first estimate of the resource at hub height, and shows why a few extra metres of tower can pay back. It also guides where to place a weather sensor.

Good to know

The power law is a rough fit. It does not account for thermal stability, sharp changes in the terrain, nearby buildings or trees, and it is less reliable above about 100 m. Measured data at the site always beat a table value. Small turbines on roofs in towns suffer from turbulence that the law does not describe.

The wind turbine power calculator turns speed into output, the wind load calculator gives the force on structures, the wind chill calculator covers the feel of the wind on skin, and the apparent wind calculator combines motion and wind for sailors.

Frequently asked questions

What is wind shear?

Wind shear here means the change of wind speed with height above the ground. Friction with the surface slows the air near the ground, so the wind gets faster as you go up. Over smooth terrain, the change is small, and over rough terrain, it is large.

What is the power law?

The wind profile power law, also called the Hellmann law, says that the wind speed at one height equals the speed at another height times the ratio of the heights raised to the exponent α. It is a simple fit to measured profiles that works well for heights up to about 100 m in neutral conditions.

Which exponent should I use?

A value of 1/7, about 0.14, is a common default for open terrain. Water has a lower exponent, around 0.10, while forests, towns and suburbs have higher ones, between 0.2 and 0.3. The best value is measured at the site with anemometers at two heights, since it also changes with the time of day and the season.

Why does the power rise so much?

The power carried by the wind is proportional to the cube of the speed. A 17 percent rise in speed means a 59 percent rise in power, since 1.168 cubed is 1.59. That is why turbines are mounted high, and why small turbines near roofs do poorly in the turbulent air of towns.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.