Skip to content
Omnikalc

Bike spoke length calculator: what length of spokes for your wheel?

Enter the rim ERD, the hub flange diameter and offsets, the spoke count and the crossing pattern to get the spoke length for each side of the wheel and the length to order.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

mm

Value out of range

Results

Spoke length, left side

291.1 mm

Spoke length, right side

289.4 mm

Order, left side (nearest 2 mm)
292 mm
Order, right side (nearest 2 mm)
290 mm
Angle between hub and rim holes
67.5 °

A spoke that is too long or too short ruins a wheel build. The length depends on the rim, the hub and the lacing pattern, and the formula is geometry. This bike spoke length calculator takes the ERD, the hub flange diameter and offsets, the number of spokes, the crossing pattern and the spoke hole diameter to give the length for each side and the length to order.

How the calculation works

  • Angle α = 720 × crossings ÷ number of spokes, in degrees. It is the angle between the hub hole and the rim hole that the spoke joins, seen from the axle.
  • Spoke length = √(R² + r² + w² − 2·R·r·cos α) − d ÷ 2, where R is half of the ERD, r half of the flange diameter, w the distance from the hub center to the flange and d the diameter of the spoke hole.
  • The left and right lengths differ when the wheel is dished, because the flanges are at different distances from the center.
  • Order length is the result rounded to the nearest 2 mm, the step in which spokes are sold.

Example

A rear wheel has an ERD of 600 mm, flanges of 58 mm diameter at 36 mm (left) and 18 mm (right), 32 spokes, 3 cross, and a spoke hole of 2.6 mm. The angle is 720 × 3 ÷ 32 = 67.5°. The left spoke is √(300² + 29² + 36² − 2 × 300 × 29 × cos 67.5°) − 1.3 = 291.1 mm, and the right spoke 289.4 mm. Order 292 mm and 290 mm.

Why it matters

Wheel builders use a spoke calculator before every build, because the spokes are cut to a fixed length and a mistake means buying a set again. The formula also shows the effect of the crossing pattern: radial lacing gives the shortest spokes, and more crossings give longer ones.

Good to know

The result is a good starting point, and builders add or subtract a millimeter for the rim’s nipple seat, the nipple type and the spoke elbow. Measure the ERD with the same nipples as the build, with the spokes tightened. For a wheel with the same offsets on both sides, such as a front wheel without disc, the two sides give the same length. Offset rims need the rim offset subtracted from the flange distance. Disc brake and thru-axle hubs often have a different flange distance on each side.

The bike chain length calculator sizes the chain, the bike gear calculator computes gear ratios and the wheel offset calculator is used for car wheels.

Frequently asked questions

How do you measure the ERD?

The effective rim diameter is the diameter of the circle on which the spoke ends sit inside the rim. Measure it by joining two rim sections with a spoke or by using the rim maker's number, and use the same nipple type that you plan to use. An error of 1 mm in the ERD changes the spoke length by 0.5 mm.

What hub measurements do I need?

The diameter of the circle through the spoke holes in each flange, and the distance from the center of the hub (halfway between the locknuts) to each flange. A caliper and a ruler are enough. Manufacturers publish these numbers in the specs.

What is the crossing pattern?

It is the number of spokes that a spoke crosses on the same side of the wheel. A 3-cross pattern is the strongest and the most common on 32 and 36 spoke wheels. A radial wheel has no crossing, and the spokes are shorter but are not suited to the drive side of a rear wheel or a disc brake.

Should I round up or down?

Spokes are sold in 1 or 2 mm steps. Choose the nearest length, and if in doubt, the shorter one, as long as the thread reaches the nipple head fully and the spoke end does not protrude from the nipple into the tire.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.