Skip to content
Omnikalc

Average end area volume calculator: earthwork between cross-sections

Enter the distance between two cross-sections and their areas, plus the middle section, to get the earthwork volume by the average end area method, the prismoidal volume and the error of the simple method.

Updated on
Your inputs
ft

Value out of range

ft²

Value out of range

ft²

Value out of range

ft²

Value out of range

Results

Volume by the average end area method

555.6 yd³

Volume by the prismoidal formula
550.6 yd³
Overestimate of the average end area
4.9 yd³
Error of the average end area method
0.9 %
Small error: the sections vary almost linearly

The average end area method computes the earthwork volume between two cross-sections from the distance and the areas. The average end area volume calculator also applies the prismoidal formula with the middle section and shows the error of the simple method.

How the calculation works

  • Enter the distance between two consecutive cross-sections of the road, the trench or the pad, and the area of each section in square feet.
  • Enter the area of the middle section, halfway between them, to check the result with the prismoidal formula.
  • The calculator applies the average end area method: V = L × (A1 + A2) / 2, and converts the volume from cubic feet to cubic yards.
  • It also computes the prismoidal volume V = L × (A1 + 4 Am + A2) / 6 and the error of the simple method.

Example

Two cross-sections of a road cut are 100 ft apart, with areas of 120 ft² and 180 ft². The average end area volume is 100 × (120 + 180) / 2 = 15,000 ft³ = 555.6 yd³. The middle section has an area of 148 ft², so the prismoidal volume is 100 × (120 + 4 × 148 + 180) / 6 = 14,866.7 ft³ = 550.6 yd³. The average end area method overestimates the volume by 4.9 yd³, or 0.9%.

Why it matters

The calculator helps surveyors, civil engineers, road and site contractors and students to estimate the cut and fill of a road, a trench, a pond or a building pad, to check the output of design software by hand, and to see if the sections are close enough. It is the basic volume formula of earthwork.

Good to know

Take the cross-sections at every change of slope and at every change from cut to fill, not only at regular intervals. Keep the areas in the same unit as the distance. Use the prismoidal formula, or add sections, when the error shown is more than 2% to 3%. Remember that the volumes are in bank yards.

The excavation calculator gives the volume of a simple hole, the concrete volume calculator handles slabs and footings, the retaining wall calculator covers walls that hold a cut and the gravel calculator estimates the stone for a base.

Frequently asked questions

What is the average end area method?

The average end area method is the standard way to compute the volume of a cut or a fill along a road, a canal or a pipeline. The volume between two cross-sections is the distance between them multiplied by the average of the two end areas: V = L × (A1 + A2) / 2. The total volume is the sum of the volumes of all the segments. It is the method that most earthwork software uses.

What is the prismoidal formula?

The prismoidal formula is more exact. It uses the area of the middle section: V = L × (A1 + 4 Am + A2) / 6, where Am is the area of the section halfway between the two ends, not the average of the end areas. It is exact for a solid that tapers in a straight line, and for a solid with a parabolic variation. It needs one more section for each segment.

When is the average end area method wrong?

The method overestimates the volume when the areas of the two ends are very different, for example at the transition between a cut and a fill, and when the ground changes shape between the sections. The error is small for sections that are close to one another and similar in area. A common rule is to keep the spacing at 50 ft (15 m) or less on a rough terrain.

How do I use the result in an estimate?

The volumes are in bank yards, in the ground. Convert them to loose volume with the swell factor for the hauling and to compacted volume with the shrinkage for the fill. Add the segments of the whole job, and compare the total cut with the total fill to find the balance. The earthwork swell and shrink calculator does this step.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.