Skip to content
Omnikalc

Blast hole calculator: explosive charge and powder factor of a bench blast

Enter the burden, the spacing, the bench height, the subdrill, the stemming, the hole diameter and the explosive to get the rock volume, the charge per hole, the powder factor and the stemming ratio.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

in

Value out of range

Results

Powder factor

0.83 lb/yd³

Usual range for a bench blast
Rock volume per hole
111.1 yd³
Explosive charge per hole
92.6 lb
Stemming to burden ratio
0.80
Normal stemming

The blast hole calculator gives the rock volume per hole, the explosive charge per hole, the powder factor and the stemming to burden ratio of a bench blast, from the burden, the spacing, the bench height, the subdrill, the stemming, the hole diameter and the explosive.

How the calculation works

  • Enter the burden, the spacing, the bench height, the subdrill and the stemming of the blast hole.
  • Enter the hole diameter and choose the explosive that is loaded in the hole.
  • The calculator finds the rock volume per hole, the explosive charge per hole, the powder factor and the stemming to burden ratio.

Example

A bench of 25 ft is drilled with holes of 4 in, a burden of 10 ft, a spacing of 12 ft, a subdrill of 3 ft and a stemming of 8 ft, and loaded with ANFO of density 0.85. Each hole breaks 10 × 12 × 25 / 27 = 111.1 yd³. The charge length is 25 + 3 − 8 = 20 ft, the loading density is 0.3405 × 0.85 × 4² = 4.63 lb/ft, and the charge is 92.6 lb. The powder factor is 92.6 / 111.1 = 0.83 lb/yd³, and the stemming to burden ratio is 0.80.

Why it matters

The calculator helps quarry and mine engineers, civil contractors, estimators and students to estimate the explosive needed for a rock excavation, to compare the pattern of the holes and to see how the burden, the spacing and the stemming change the powder factor and the cost.

Good to know

Start from a proven pattern for the same rock and adjust it from the results of the fragmentation, the muck pile and the vibration records. Survey the face before drilling, because a burden that varies a lot gives flyrock. Keep the stemming with a clean angular crushed stone and never reduce it to save the length of the hole, and let only a licensed blaster load and fire the shot.

The tunnel rock support Q-system calculator rates the rock mass, the excavation calculator gives the volume of rock to remove, the earthwork swell and shrink calculator converts the bank volume to the loose volume and the density calculator converts the mass and the volume.

Frequently asked questions

What is the powder factor?

The powder factor is the mass of explosive used for each unit of rock volume, in lb/yd³ or in kg/m³. It is the main indicator of the cost and of the energy of a blast. A hard and massive rock needs a higher value than a soft and fractured rock, and a typical bench blast in quarrying is about 0.5 to 1.0 lb/yd³ (0.3 to 0.6 kg/m³).

How is the charge of a hole calculated?

The explosive is loaded from the bottom of the hole, over the bench height plus the subdrill and minus the stemming. The mass per unit length is the area of the hole times the density of the explosive, which is 0.3405 times the density in g/cm³ times the square of the diameter in inches, in lb/ft. The charge is this loading density times the length of the charge.

What are the burden, the spacing and the stemming?

The burden is the distance between the hole and the free face, and the spacing is the distance between the holes in a row. A common rule is a burden of 25 to 35 times the hole diameter, a spacing of 1.0 to 1.5 times the burden, and a stemming of about 0.7 times the burden. A stemming that is too short causes flyrock and an air blast, and a stemming that is too long leaves the top of the bench in blocks.

What are the limits of the calculator?

The calculator gives the charge of a single column of explosive in a vertical hole. It does not include the decks, the primers, the delay timing, the water in the holes, the vibration and the air blast limits, the geology or the fragmentation target. A blast must be designed and fired by a licensed blaster, with the rules of the authority, and only the licensed blaster can approve the loads.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.