Skip to content
Omnikalc

Tunnel rock support calculator: preliminary rock bolt length and support pressure with the Q-system

Enter the rock mass quality Q, Jn, Jr, the excavation support ratio and the span to get the maximum unsupported span, the rock bolt length and the roof support pressure of Barton’s Q-system.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

ft

Value out of range

Results

Rock bolt length (Barton)

9.0 ft

Maximum span that can stand unsupported
18.3 ft
Span over the maximum unsupported span
1.42
Support is needed: bolts and shotcrete
Roof support pressure (Barton)
11.9 psi

The tunnel rock support calculator gives the maximum span without support, the rock bolt length and the roof support pressure of an underground opening from the Q-system index, the joint numbers, the excavation support ratio and the span, with the empirical formulas of Barton.

How the calculation works

  • Enter the rock mass quality Q from the Q-system classification, with the joint set number Jn and the joint roughness Jr of the roof.
  • Choose the excavation support ratio ESR from the use of the opening, and enter the span or diameter of the opening.
  • The calculator finds the maximum span without support 2 ESR Q^0.4 and compares it with your span.
  • It gives the rock bolt length L = 2 + 0.15 B / ESR and the roof support pressure from the formulas of Barton.

Example

A rock mass with Q = 4, Jn = 9 and Jr = 1.5 is used for a permanent opening (ESR = 1.6) with a span of 26 ft. The maximum unsupported span is 2 × 1.6 × 4^0.4 = 5.57 m, or 18.3 ft, so the span is 1.42 times larger and needs support. The bolt length is 2 + 0.15 × 7.92 / 1.6 = 2.74 m, or 9.0 ft. The roof support pressure is 2 × √9 / (3 × 1.5 × 4^(1/3)) = 0.84 kg/cm², or 11.9 psi.

Why it matters

The calculator helps geotechnical and mining engineers, tunnel designers and students to make a preliminary estimate of the rock support of a tunnel, a cavern or a mine opening, and to see the effect of the rock quality and of the span. It gives the numbers that go with the support chart of the Q-system.

Good to know

Obtain Q from the rock mapping and the borehole logs, with a range of values and not a single one. Take the ESR for the use of the opening. Compare the results with the support chart, and use them only as a first estimate. Adapt the support during the excavation, and follow the standards and the advice of a rock mechanics engineer for the final design.

The Rankine earth pressure calculator covers soil pressure, the pile capacity calculator covers deep foundations, the factor of safety calculator checks margins and the Vs30 calculator classifies the site.

Frequently asked questions

What is the Q-system?

The Q-system of Barton, Lien and Lunde (1974) classifies the quality of a rock mass for tunnel support with the index Q = (RQD / Jn) (Jr / Ja) (Jw / SRF), which combines the block size, the shear strength between blocks and the active stress. Q goes from 0.001 for exceptionally poor rock to 1,000 for exceptionally good rock. The index is used to choose rock bolts, shotcrete and other support from a chart.

What is the excavation support ratio?

The ESR accounts for the use of the opening and the degree of safety required. A temporary mine opening can accept a higher risk (ESR = 3.5), while a power station or a major road tunnel needs a very safe support (ESR = 1.0). The span is divided by the ESR to give the equivalent dimension of the support chart, so a lower ESR means a heavier support.

What do the formulas give?

The maximum span without support is 2 ESR Q^0.4 in meters. The length of the rock bolts in the roof is L = 2 + 0.15 B / ESR in meters, and the ultimate roof support pressure is Proof = 2 √Jn Q^(−1/3) / (3 Jr) in kg/cm². These are empirical formulas for a preliminary estimate, and they apply to openings in jointed rock with spans of 2 to 40 m.

What are the limits of the method?

The Q-system is an empirical method that is based on case histories of tunnels. Q must be measured from the borehole cores and the mapping of the rock, and the support must be adapted during the excavation with the observation of the rock. In squeezing ground, in swelling clays and in very high stresses, other methods are needed. The final support design requires a rock engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.