Skip to content
Omnikalc

Bond comminution energy calculator: energy and power to grind an ore

Enter the Bond work index, the feed size F80, the product size P80 and the throughput to get the grinding energy in kWh per ton, the mill power, the motor power and the size reduction ratio.

Updated on
Your inputs
kWh/short ton

Value out of range

µm

Value out of range

µm

Value out of range

short tons/h

Value out of range

%

Value out of range

Results

Specific energy (Bond's law)

9.43 kWh/short ton

Power needed at the mill
471.4 kW
Motor power input
665.1 hp
Size reduction ratio
80.0
Ratio within the range of a grinding stage

The Bond comminution energy calculator applies Bond’s law to give the specific energy, the mill power, the motor power and the size reduction ratio for crushing or grinding a material from the feed size F80 to the product size P80 with a given work index.

How the calculation works

  • Enter the Bond work index Wi of the ore (about 13 kWh/short ton for many ores, 15 to 20 for hard ones), and the feed size F80 and product size P80 in micrometers.
  • F80 and P80 are the sizes through which 80% of the material passes in the feed and in the product, read from the size distribution curves.
  • The calculator applies Bond’s law, W = 10 Wi (1 / √P80 − 1 / √F80), to give the specific energy in kWh per short ton.
  • It multiplies it by the throughput to get the power at the mill, and by the drive efficiency to get the motor power, with the size reduction ratio.

Example

An ore with a work index of 13 kWh/short ton is ground from an F80 of 12,000 µm to a P80 of 150 µm at 50 short tons/h. The specific energy is 10 × 13 × (1 / √150 − 1 / √12,000) = 130 × (0.08165 − 0.00913) = 9.43 kWh/short ton. The power at the mill is 9.43 × 50 = 471.4 kW. With a drive efficiency of 95%, the motor input is 471.4 / 0.95 / 0.746 = 665.1 hp. The reduction ratio is 80.0.

Why it matters

The calculator helps mineral processing engineers, quarry and cement plant managers, process students and consultants to estimate the energy and power of a mill, to compare the cost of a finer product and to check an existing circuit. It also shows how much the power rises as the product becomes finer.

Good to know

Use the work index measured on the real ore, and not a table value, for a final design. Read F80 and P80 from the sieve curves, not from the top size. Apply Bond’s correction factors for dry grinding, small mills and fine products. Keep a margin of 10 to 15% on the mill motor.

The power factor correction calculator covers the electric side, the horsepower and torque calculator converts the motor power, the motor current calculator checks the supply and the density calculator converts masses and volumes of the ore.

Frequently asked questions

What is Bond’s law of comminution?

Bond’s third theory of comminution says that the energy to reduce the size of a material is proportional to the new crack length created. It gives W = 10 Wi (1 / √P80 − 1 / √F80), where Wi is the work index of the material, and P80 and F80 are the 80% passing sizes of the product and of the feed in micrometers. It is the most used method to estimate the power of crushers and ball mills.

What is the Bond work index?

The work index is the energy in kWh per ton needed to reduce a material from an infinite size to 80% passing 100 µm. It is measured in a standard laboratory test, for crushing, rod milling or ball milling. Soft materials such as coal or limestone are below 10, usual ores are 10 to 16, and hard ores such as quartzite or taconite exceed 15 to 20. The index may differ with the size range.

What are the limits of the method?

The calculated energy applies to the mill shaft in wet grinding with a standard mill diameter and a standard efficiency. Bond’s paper also gives correction factors for dry grinding, for a mill that is smaller or larger than 8 ft in diameter, for a very coarse feed, for very fine products under about 75 µm and for open-circuit milling. Without these factors the result is only a first estimate, accurate to about 20%.

How is the motor power chosen?

The power at the mill is the specific energy times the throughput, and the motor input is that power divided by the drive efficiency, which is 0.90 to 0.95 for a mill with a gear drive. Mills are sized with a margin of 10 to 15% over the calculated power for the variation of the ore hardness. The motor power in horsepower is the kilowatts divided by 0.746.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.