Skip to content
Omnikalc

Concrete yield calculator: volume of a batch from the absolute volume method

Enter the weights of cement, water and aggregates, the air content and the specific gravities to get the absolute volume, the yield of the batch, the unit weight and the water-cement ratio.

Updated on
Your inputs
lb

Value out of range

lb

Value out of range

lb

Value out of range

lb

Value out of range

%

Value out of range

Value out of range

Value out of range

Value out of range

Results

Yield of the batch

1.000 yd³

The batch gives one cubic yard
Absolute volume of the ingredients
25.65 ft³
Volume of the batch with air
27.00 ft³
Unit weight of the fresh concrete
142.8 lb/ft³
Water-cement ratio
0.496

The concrete yield calculator gives the absolute volume of the ingredients, the volume with air, the yield of the batch, the unit weight of the fresh concrete and the water-cement ratio, from the weights of the ingredients, the air content and the specific gravities.

How the calculation works

  • Enter the weights of the cement, the water, the coarse aggregate and the fine aggregate of the batch, and the air content.
  • Enter the specific gravity of the cement and of the two aggregates, from the supplier data.
  • The calculator finds the absolute volume of the ingredients, the volume with air, the yield of the batch, the unit weight and the water-cement ratio.

Example

A mix has 564 lb of cement, 280 lb of water, 1,750 lb of coarse aggregate and 1,260 lb of fine aggregate, with 5 % of air. The absolute volumes are 2.87 + 4.49 + 10.58 + 7.71 = 25.65 ft³. The volume with air is 25.65 / (1 − 0.05) = 27.00 ft³, so the yield is 27.00 / 27 = 1.000 yd³. The unit weight is 3,854 / 27.00 = 142.8 lb/ft³, and the water-cement ratio is 280 / 564 = 0.496.

Why it matters

The calculator helps concrete technologists, mix designers, quality control staff, suppliers and students to check that a mix proportions gives the right volume, to adjust a trial batch and to compare the unit weight with the measured value of the test on the fresh concrete.

Good to know

Use the specific gravities measured on the real materials and the weights corrected for the moisture of the aggregates. Compare the calculated unit weight with the measured unit weight of the fresh concrete, and adjust the batch weights if the difference is more than 1 or 2 %. Keep the cement content, the water-cement ratio and the air content within the project specification when you adjust the proportions of the aggregates.

The concrete volume calculator gives the quantity of concrete for a shape, the concrete crack width calculator checks the cracking, the density calculator converts the mass and the volume and the soil unit weight calculator handles the weights of the soil.

Frequently asked questions

What is the absolute volume method?

The absolute volume method gives the volume of the concrete as the sum of the volumes of the solid particles of each ingredient, the volume of the water and the volume of the air. The volume of an ingredient is its weight divided by its specific gravity times the unit weight of water. It is the basis of the concrete mix design of ACI 211 and a way to check if a proportioned mix gives the cubic yard that is expected.

What is the yield of a concrete batch?

The yield is the volume of fresh concrete produced by a batch, in cubic yards or in cubic meters. A yield below 1.00 means that the mix has less concrete than expected, and the supplier loses money or the buyer is short. A yield over 1.00 means that the mix has more volume, usually because the air content is high or the aggregates are lighter than the data, and it may give a lower strength for the cement used.

Why are saturated surface dry weights used?

The aggregates in a mix have pores that can hold water. In the saturated surface dry condition, the pores are full and the surface is dry, so the aggregate neither adds water to the mix nor takes it. The weights from the field are corrected for the moisture, and the specific gravities used for the volume are the values in the SSD condition.

What are the limits of the calculator?

The calculator uses the weights and the specific gravities that you enter and does not include the admixtures, the supplementary cementitious materials with a different gravity, the moisture of the aggregates, the voids caused by a poor consolidation, the waste on site or the water added at the job. The yield of a truck is best checked with the unit weight test of ASTM C138.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.