Skip to content
Omnikalc

Soil unit weight calculator: phase relations of a soil

Enter the specific gravity of the grains, the water content and the void ratio of a soil to get the degree of saturation, the dry, moist, saturated and buoyant unit weights and the porosity.

Updated on
Your inputs

Value out of range

%

Value out of range

Value out of range

Results

Degree of saturation S = w Gs / e

62.3 %

Partly saturated
Dry unit weight γd
102.11 pcf
Moist (total) unit weight γ
117.43 pcf
Saturated unit weight γsat
126.69 pcf
Buoyant unit weight γ′
64.29 pcf
Porosity n
39.4 %

The phase relations connect the unit weights, the water content and the void ratio of a soil. The soil unit weight calculator gives the degree of saturation, the dry, moist, saturated and buoyant unit weights and the porosity from Gs, w and e.

How the calculation works

  • Enter the specific gravity of the soil grains Gs (about 2.65 for sand, 2.70 for clay), the water content w in percent and the void ratio e.
  • The calculator finds the degree of saturation S = w Gs / e, which links the three phases of the soil: solids, water and air.
  • It computes the dry, moist, saturated and buoyant unit weights with γw = 62.4 pcf, and the porosity n = e / (1 + e).
  • If S comes out above 100%, the inputs are not consistent: reduce the water content or increase the void ratio.

Example

A soil has Gs = 2.70, a water content w = 15% and a void ratio e = 0.65. The degree of saturation is 0.15 × 2.70 / 0.65 = 62.3%. The dry unit weight is 2.70 × 62.4 / 1.65 = 102.11 pcf and the moist unit weight is 2.70 × 1.15 × 62.4 / 1.65 = 117.43 pcf. If the soil were saturated, it would weigh 126.69 pcf, and its buoyant unit weight under the water table would be 64.29 pcf. The porosity is 39.4%.

Why it matters

The calculator helps geotechnical engineers, students and site technicians to turn a lab report into the unit weights that they need for a stress, an earth pressure or a settlement calculation, and to check that a set of measured values is consistent. It is the basic bookkeeping of soil mechanics.

Good to know

Measure the water content by oven drying and the density on an undisturbed sample, then compute e from them. If the computed saturation is above 100%, look for an error in the measurements before using the results. Use a typical Gs only for a first estimate, and a measured value for a final design.

The porosity and void ratio calculator covers the volumes, the soil compaction calculator controls the dry unit weight in a fill, the Rankine earth pressure calculator uses the unit weight to load a wall and Darcy’s law calculator computes the flow through the voids.

Frequently asked questions

What are the phase relations of a soil?

A soil is a mixture of three phases: solid grains, water and air in the voids. The phase relations connect the volumes and the weights of the phases with a few parameters: the void ratio e, the water content w, the specific gravity of the grains Gs and the degree of saturation S. They satisfy the basic identity S e = w Gs. Knowing three independent parameters gives all the others.

What is the difference between the unit weights?

The dry unit weight γd is the weight of the grains per unit of total volume. The moist (or total) unit weight γ includes the water that the soil holds at its water content. The saturated unit weight γsat is the weight when all the voids are full of water. The buoyant (or submerged) unit weight γ′ = γsat − γw is the effective weight of a soil below the water table.

Why is the degree of saturation limited to 100%?

The water cannot fill more than the voids. For given Gs and e, the largest possible water content is e / Gs, which gives S = 100%. If the calculator shows a degree of saturation above 100%, the inputs do not describe a real soil: the water content is too high or the void ratio is too low. The case often comes from a typing error or a wrong Gs.

Where are these values used?

The unit weights feed the vertical stress in a soil profile, the earth pressure on a wall, the bearing capacity of a footing and the settlement of a layer. Use the moist unit weight above the water table and the buoyant unit weight below it for the effective stress. The dry unit weight is the quantity that a compaction specification controls.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.