Skip to content
Omnikalc

Corrosion rate calculator: how fast is the metal wasting away?

Enter the weight loss, the metal, the area and the exposure time to get the corrosion rate in mils per year and the service life of your allowance.

Updated on
Your inputs
mg

Value out of range

in²

Value out of range

hours

Value out of range

mils

Value out of range

Results

Corrosion rate

5.66 mpy

Fair to good (5 to 20 mpy): fine for non-critical parts
Corrosion rate in millimetres per year
0.144 mm/yr
Years until the allowance is used up
22.1 years
Mass loss per area per day (mdd)
31.0 mdd
Penetration over the test
0.47 mils

Choosing a metal for a tank, a pipe or a fitting depends on how fast it will corrode in service. The corrosion rate calculator takes the weight loss of a test coupon, the metal, the exposed area, the exposure time and a corrosion allowance, and gives the corrosion rate in mils per year, the rate in mm per year, the years until the allowance is used up, the mass loss per area per day and the penetration during the test.

How the calculation works

  • Enter the weight loss of the test coupon in milligrams, after the corrosion products have been cleaned off and the coupon weighed again.
  • Choose the metal, which sets the density, and enter the exposed area in square inches and the exposure time in hours.
  • Enter the corrosion allowance, which is the thickness of metal that the part can lose before it must be replaced, in mils (1 mil is 0.001 inch).
  • The rate in mils per year is 534 × W ÷ (D × A × T), with W in mg, D in g/cm³, A in square inches and T in hours. The calculator then converts it to millimetres per year and finds the service life of the allowance.

Example

A carbon steel coupon of 2 in² loses 120 mg after 720 hours (30 days) in a test solution. The rate is 534 × 120 ÷ (7.86 × 2 × 720) = 5.66 mpy, which is 0.144 mm/yr. That is 31 mdd. With a corrosion allowance of 125 mils (1/8 inch), the part lasts about 125 ÷ 5.66 = 22 years. A rate over 20 mpy would use up the allowance in about 6 years.

Why it matters

A rate turns a laboratory weight loss into a service life, which is what a designer needs. It lets you compare materials and coatings on a common scale, plan inspections, and set a corrosion allowance that is neither wasteful nor risky.

Good to know

The formula assumes uniform corrosion over the whole surface. Localised attack such as pitting can be many times faster than the average, so a low rate does not guarantee a long life. For safety-critical items, use inspection data, the standards of your industry and an engineer who knows the environment.

The electroplating calculator covers coatings that protect metal, the pressure vessel stress calculator shows the thickness needed for pressure, the factor of safety calculator sets margins, and the pipe flow velocity calculator checks velocities that can speed up erosion and corrosion.

Frequently asked questions

How is the corrosion rate found from weight loss?

A coupon of the metal is weighed, exposed to the environment for a known time, cleaned and weighed again. The weight loss, divided by the density, the area and the time, gives the thickness lost per unit time. The ASTM G1 and G31 practices describe the method and the cleaning.

What is a mil and an mpy?

A mil is one thousandth of an inch, or 0.0254 mm. The corrosion rate in the United States is often given in mils per year, written mpy. A rate of 5 mpy is 0.127 mm per year. Outside the United States, the rate is more often given in mm per year or µm per year.

What is a good corrosion rate?

Under 1 mpy is outstanding, 1 to 5 mpy is excellent, 5 to 20 mpy is good enough for many uses, 20 to 50 mpy is fair, and above 50 mpy is poor to unacceptable. The right limit depends on the part, its thickness, the safety margin and the cost of failure.

What are the limits of the method?

It gives an average rate across the surface. Pitting, crevice corrosion, cracking and galvanic effects can destroy the metal much faster than the average suggests. Short tests may also miss changes with time, as films form or break down. Treat the result as a guide and use inspection for critical equipment.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.