Skip to content
Omnikalc

Fan affinity laws calculator: what happens when you change fan speed or impeller size?

Enter the current and new speed or diameter and the current airflow, pressure and power to get the new values from the fan laws.

Updated on
Your inputs
rpm

Value out of range

rpm

Value out of range

in

Value out of range

in

Value out of range

CFM

Value out of range

in. wg

Value out of range

hp

Value out of range

Results

New shaft power

1.95 hp

More power: check the motor rating and the drive
New airflow
2,500 CFM
New static pressure
2.34 in. wg
Change in shaft power
95.3 %
Speed ratio
1.250

Fans follow simple scaling rules that let you predict the effect of a speed change without a new test. The fan affinity laws calculator takes the current and new speed, the current and new impeller diameter, and the current airflow, pressure and power, and gives the new airflow, the new static pressure, the new shaft power, the change in power and the speed ratio.

How the calculation works

  • Enter the current and new fan speeds in rpm. The impeller diameters can stay equal if only the speed changes.
  • Enter the current airflow, static pressure and shaft power from the fan curve or a measurement.
  • The affinity laws scale the values: airflow × (N₂/N₁) × (D₂/D₁)³, pressure × (N₂/N₁)² × (D₂/D₁)² and power × (N₂/N₁)³ × (D₂/D₁)⁵.
  • Check the new shaft power against the motor rating, since power grows with the cube of the speed.

Example

A fan runs at 1,200 rpm and moves 2,000 CFM at 1.5 in. wg with 1 hp at the shaft. Raising the speed to 1,500 rpm gives a ratio of 1.25. Airflow rises to 2,500 CFM, pressure to 1.5 × 1.25² = 2.34 in. wg and power to 1 × 1.25³ = 1.95 hp, which is 95 % more. A speed increase of 25 percent nearly doubles the power draw, which is why a small speed reduction saves so much energy.

Why it matters

The laws show that fan speed is a strong lever on energy use. A small increase to get a bit more air can overload a motor, while a modest reduction in speed gives a large saving. They also help size a drive or a motor when you change the speed of an existing fan, and they check a vendor’s claims.

Good to know

The laws assume the same fan, the same air density and a system that scales with the flow squared. In a real duct with a fixed damper or filter loading, the operating point may not follow the curve exactly. Check the motor rating, the maximum safe speed of the wheel and the noise, which rises steeply with speed, before changing a fan.

The bathroom fan and ceiling fan calculators help choose a fan, the duct size calculator checks that the duct suits the airflow, and the fan cost calculator estimates the running cost of the power found here.

Frequently asked questions

What are the fan affinity laws?

They are three rules that link how a fan performs at different speeds or impeller diameters, for the same fan type and air density. Airflow varies with speed, pressure varies with the square of the speed and power varies with the cube of the speed. They apply to similar fans and to a fan whose speed changes.

Why does a small speed cut save so much energy?

Because power follows the cube of the speed. Slowing a fan by 20 percent cuts the airflow by 20 percent but the power by about 49 percent, since 0.8³ is 0.512. This is why variable speed drives are common on fans that do not need to run at full speed all the time.

Do the laws work for any change?

They are accurate for moderate speed changes of the same fan in the same system with the same air density. They become less reliable with big changes, at high speeds where the air compresses or when the system curve is very different. For a precise result, read the real fan curve from the maker.

What about the impeller diameter?

For a trimmed or smaller impeller in the same casing, the airflow varies with the cube of the diameter, the pressure with the square and the power with the fifth power. The fifth power only holds for homologous impellers, so for small trims the real change is usually a bit smaller.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.