Skip to content
Omnikalc

Gambrel roof calculator: rafter lengths, area and extra space

Enter the width, length, ridge height and break point of a gambrel roof to get the two rafter lengths, the roof area, the attic volume and the slope angles.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

%

Value out of range

%

Value out of range

Results

Lower rafter length (per side)

8.22 ft

Upper rafter length (per side)
9.36 ft
Roof surface area (without overhang)
1,055 sq ft
Attic volume under the roof
5,486 cu ft
Extra volume compared with a plain gable roof of the same height
27.0%
Lower slope angle
61.2 °
Upper slope angle
30.8 °

A gambrel roof is the barn roof: two slopes on each side, a steep lower one and a gentler upper one. The shape gives a tall, boxy attic that can hold a loft, a workshop or hay, for the same ridge height as a simple gable. This calculator takes the building width and length, the ridge height and the position of the break, and returns the rafter lengths, the roof area, the attic volume and the two slope angles.

How the calculation works

With half the span s, the break point sits at a horizontal distance x₁ from the wall and a height y₁.

  • Lower rafter = √(x₁² + y₁²)
  • Upper rafter = √((s − x₁)² + (H − y₁)²)
  • Roof area = 2 × length × (lower rafter + upper rafter)
  • Cross-section = s × y₁ + s × H − x₁ × H, and volume = cross-section × length
  • Slope angles = arctan(rise ÷ run) for each slope

Example

A building 24 ft wide and 30 ft long, 12 ft from the wall top to the ridge, with the break at 33 % of the half span (3.96 ft) and 60 % of the height (7.2 ft). The lower rafter is 8.22 ft at 61.2°, the upper rafter 9.36 ft at 30.8°. The roof area is 1,055 sq ft before overhangs, and the volume under the roof is 5,486 cu ft, which is 27 % more than a gable roof of the same height (4,320 cu ft).

Why it matters

The extra volume is why the gambrel is used for barns, sheds and garden offices: the near-vertical lower slope turns roof space into walls, so a person can stand near the eaves. It also helps with budget, because short rafters can be prefabricated as trusses. The trade-off is a flatter upper slope, which sheds snow less well, and more joints that need good flashing.

Good to know

Add the overhang, the ridge cut and the plumb cuts to each rafter length before ordering lumber. Snow regions need an upper slope steeper than about 4 in 12. The break point must be supported by a collar tie or a gusset, and building codes set the sizes of rafters by span and load, so have a design checked before building. This tool is for education and planning.

In practice

Sketch the half profile on graph paper, then try break points of 25 to 40 % of the half span and 55 to 70 % of the height. Choose the proportions that give an upper slope of at least 4 in 12 and a lower slope near 60°, and order roofing for the area plus 10 % waste.

The rafter length calculator handles a simple gable, the roofing calculator estimates squares and shingles, and the attic conversion calculator plans the space under the roof.

Frequently asked questions

What is a gambrel roof?

A gambrel roof is a two-sided roof with two slopes on each side: a steep lower slope and a shallower upper slope. It is the classic barn roof, and it gives much more headroom and usable space under the roof than a gable roof of the same height.

How do I choose the break point?

A common proportion is a lower slope of about 60 degrees and an upper slope of about 30 degrees, with the break roughly one third of the way across half the span and at 60 percent of the height. Moving the break outward adds space but makes the upper slope flatter.

How long are the rafters?

Each rafter is the hypotenuse of a right triangle made of its horizontal run and its vertical rise. The lower rafter runs from the wall to the break, and the upper rafter runs from the break to the ridge. Add the overhang and the cuts separately.

How much extra space do I gain?

For the default proportions the cross-section is about 27 percent larger than that of a gable roof of the same width and height. The gain grows when the break is higher and nearer the wall.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.