Skip to content
Omnikalc

Haul truck calculator: rimpull and speed of a loaded truck on a haul road grade

Enter the truck weight, the rolling resistance, the grade, the engine power, the efficiency and the traction to get the total resistance, the rimpull required, the maximum speed and the traction ratio.

Updated on
Your inputs
tons

Value out of range

%

Value out of range

hp

Value out of range

Value out of range

Value out of range

Results

Maximum speed on the grade

12.3 mph

Total resistance (rolling + grade)
13.0 %
Tractive force required (rimpull)
20,800 lb
Required rimpull to usable traction ratio
0.31
The wheels have enough traction

The haul truck calculator gives the total resistance, the rimpull required, the maximum speed on a grade and the traction ratio of a loaded truck on a haul road, from the weight, the rolling resistance, the grade, the engine power and the traction.

How the calculation works

  • Enter the gross weight of the loaded truck, choose the rolling resistance of the haul road and enter the grade.
  • Enter the engine power, the efficiency of the drive train, the coefficient of traction of the surface and the share of the weight on the driving wheels.
  • The calculator finds the total resistance in percent of grade, the tractive force required, the maximum speed the engine can sustain and the ratio of the force required to the usable traction.

Example

A truck weighs 80 tons loaded, on a packed road with a rolling resistance of 100 lb/ton and an uphill grade of 8 %, which adds 20 × 8 = 160 lb/ton. The total resistance is 260 lb/ton, or 13.0 %. The force required is 80 × 260 = 20,800 lb. With 800 hp and an efficiency of 0.85, the maximum speed is 375 × 800 × 0.85 / 20,800 = 12.3 mph. The usable traction is 0.6 × 0.7 × 160,000 = 67,200 lb, so the ratio is 0.31.

Why it matters

The calculator helps earthwork and mining engineers, estimators, haul road designers and students to check if a truck can climb a ramp, to find its speed on a grade and to compare the effect of the rolling resistance and the grade on the cycle time.

Good to know

Maintain the haul road to keep the rolling resistance low, use the real weight of the loaded truck, and design the ramps with a grade of 8 to 10 % or less. Add the safety berms and drainage, and use the retarder chart of the manufacturer for the downhill loaded trucks.

The earthwork swell and shrink calculator converts the volumes to haul, the excavation calculator gives the volume, the labor productivity calculator gives the work output and the stopping distance calculator checks the braking.

Frequently asked questions

What is rimpull?

Rimpull is the tractive force that the driving wheels can apply on the ground at the tires, and it is the force that moves the truck. It is limited by the engine power and the gear, with the speed, and by the traction between the tires and the road, with the weight on the driving wheels. A truck can climb a grade only if the rimpull available is higher than the total resistance.

How is the total resistance found?

The total resistance is the sum of the rolling resistance and the grade resistance. The rolling resistance depends on the road and the tires: about 40 lb per ton (2 %) on a hard and smooth road and 100 to 200 lb per ton on soft ground. The grade resistance is 20 lb per ton for each 1 % of grade, going up. The sum in lb/ton divided by 20 is the effective grade in percent, which is a useful way to compare the roads.

How is the maximum speed found?

With the engine power, the force and the speed are related by P = F V. In US units, the speed in mph is 375 times the horsepower times the efficiency, divided by the force in pounds. In SI units, the speed in m/s is the power times the efficiency divided by the force. The real speed is also limited by the gears, by the engine speed, by the safety on the grade and by the retarders on the downhill.

What are the limits of the calculator?

The calculator gives a steady speed on a constant grade. It does not include the acceleration, the altitude that reduces the engine power, the curves, the speed limits of the haul road, the retarding on the downhill, the tire slip or the rolling resistance of the real surface, which can change a lot with the rain. The cycle time and the production of a fleet need a more complete analysis by the haul road designer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.