Skip to content
Omnikalc

Hopper outlet size calculator: minimum outlet to prevent arching of a bulk solid

Enter the hopper wall angle, the bulk density and the unconfined yield strength of the material to get the minimum outlet diameter for a conical hopper, the minimum slot width and the recommended sizes with a margin.

Updated on
Your inputs
°

Value out of range

lbf/ft²

Value out of range

lb/ft³

Value out of range

%

Value out of range

Results

Minimum diameter of a conical outlet

19.3 in

Recommended conical outlet diameter (with margin)
23.2 in
Minimum width of a slot outlet
9.1 in
Recommended slot width (with margin)
10.9 in
Minimum slot length (3 times the width)
32.8 in

The hopper outlet size calculator uses Jenike’s arching criterion to give the minimum outlet of a conical hopper and of a slot hopper to prevent arching of a bulk solid, and the recommended sizes with a safety margin.

How the calculation works

  • Enter the wall angle of the hopper measured from the vertical (the half angle) and the bulk density of the material.
  • Enter the unconfined yield strength fc of the material at the consolidation pressure at the outlet, from a shear cell test or from published data for similar materials.
  • The calculator applies Jenike’s arching criterion B = H(θ) × fc / (ρ g), with H = 2 + θ/60 for a conical hopper and H = 1 + θ/180 for a slot.
  • It gives the minimum outlet for a conical hopper and for a slot, the recommended size with a safety margin, and the minimum slot length.

Example

A material of 60 lb/ft³ has an unconfined yield strength of 40 lbf/ft² at the outlet, and the hopper walls are 25° from the vertical. For a conical outlet, H = 2 + 25 / 60 = 2.417, so the minimum diameter is 2.417 × 40 / 60 = 1.611 ft, or 19.3 in. With a 20% margin, the recommended diameter is 23.2 in. For a slot, H = 1 + 25 / 180 = 1.139, so the minimum width is 9.1 in and the recommended width is 10.9 in, with a length of at least 32.8 in.

Why it matters

The calculator helps process and plant engineers, silo and bin designers, farmers, food and pharmaceutical processors and students to estimate the size of an outlet, to find why a bin stops flowing and to compare materials. It gives a feel for the size needed before a bulk solids test.

Good to know

Measure fc with a shear cell at the stress of the outlet, and for the worst case of moisture and storage time. Use the larger of the two results of arching and ratholing. Choose a feeder that draws over the whole outlet. Never rely on vibrators alone to cure a design problem.

The angle of repose calculator covers a pile of material, the grain bin calculator covers storage capacity, the density calculator converts masses and volumes and the screw conveyor capacity calculator sizes a feeder.

Frequently asked questions

What is arching in a hopper?

Arching happens when the particles of a bulk solid lock into a stable arch across the outlet and block the flow. A cohesive powder under the pressure of the material above it gains strength, and if that strength is large enough to carry the arch, the hopper stops flowing. The remedy is a larger outlet, steeper walls, a smoother wall lining or a feeder that draws the material over the full outlet.

How does Jenike’s criterion work?

Jenike compared the strength that the material gains while it is stored with the stress that an arch of a given span would need to carry its own weight. The minimum outlet B is the span at which the arch is just too weak to stand: B = H(θ) fc / (ρ g), where fc is the unconfined yield strength at the stress that the material has at the outlet. The factor H depends on the wall angle and the hopper shape.

What is the difference between a cone and a slot?

A conical (or square pyramid) outlet needs a larger opening than a slot, about twice as large for the same material, since an arch in a slot only spans the short direction. A slot outlet must be at least 3 times as long as it is wide for the plane-flow formula to apply, and the feeder must pull material along the whole length of the slot.

What are the limits of this calculation?

The value of fc depends on the consolidation stress, the storage time at rest and the moisture and temperature of the material, and it must be measured with a shear cell for a reliable design. The calculator also does not cover ratholing in funnel-flow bins, which depends on another criterion, nor the wall friction needed for mass flow. Use it for a first estimate and have a bulk solids test done for the final design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.