Skip to content
Omnikalc

Screw conveyor capacity calculator: how much an auger carries

Enter the screw diameter, shaft, pitch, speed and trough loading, with the density of the material, to get the capacity in ft³/h and tons/h, the speed of the material, the tip speed and the power needed.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

rpm

Value out of range

%

Value out of range

lb/ft³

Value out of range

ft

Value out of range

Value out of range

%

Value out of range

Results

Mass flow rate

5.55 tons/h

Volumetric capacity
222.0 ft³/h
Speed of the material along the trough
30.0 ft/min
Power at the screw shaft (motor input)
0.264 hp
Tip speed of the screw
94.2 ft/min
Tip speed within a normal range

A screw conveyor, or auger, moves bulk material along a trough with a turning helix. The screw conveyor capacity calculator gives the volume and mass carried per hour, the speed of the material, the tip speed and the shaft power from the geometry, the speed and the loading.

How the calculation works

  • Enter the outside diameter, the shaft diameter and the pitch of the screw, then its speed in rpm and the trough loading (30% for most materials, 15% for abrasive ones).
  • Enter the bulk density of the material, the length of the conveyor, a friction factor for the material and the drive efficiency.
  • The calculator finds the volume carried per revolution, (π/4)(D² − d²) × pitch, and multiplies it by the speed and the loading to get the capacity.
  • It gives the mass flow, the speed of the material, the shaft power to move the load and the tip speed of the screw.

Example

A screw conveyor has a 9 in screw on a 2.375 in shaft, a 9 in pitch and runs at 40 rpm with a 30% loading. The annular area is 0.7854 × (81 − 5.64) = 59.2 in², which carries 533 in³ per revolution. The capacity is 222.0 ft³/h. With a material of 50 lb/ft³, the mass flow is 5.55 tons/h and the material moves at 30.0 ft/min. With 20 ft of length, a friction factor of 2 and a drive efficiency of 85%, the shaft power is 0.264 hp.

Why it matters

The calculator helps plant engineers, farm and grain handling designers, food and feed processors, and students to size a screw conveyor, to check an existing one against the required flow, and to estimate the drive. It also helps compare a bigger slow screw with a smaller faster one.

Good to know

Choose the loading from the type of material, not from the wish to move more. Do not run abrasive materials at high speed. Reduce the capacity strongly for inclines above 10 degrees, where a horizontal formula no longer holds. Check the manufacturer’s tables for the final selection of the drive and the hanger bearings.

The grain bin calculator gives the volume of the storage, the motor current calculator checks the electric supply, the density calculator converts mass and volume and the gear ratio calculator sizes the reducer of the drive.

Frequently asked questions

How is the capacity of a screw conveyor computed?

Each turn of the screw moves a volume equal to the annular area between the screw and the shaft, (π/4)(D² − d²), times the pitch, times the share of the trough that is filled. Multiplying by the speed gives the volume per minute, and by 60 the volume per hour. The mass flow is the volume times the bulk density. For a horizontal screw this is a good estimate, but an incline reduces the capacity a lot.

What is a normal trough loading?

A loading of 45% is used for free-flowing, non-abrasive materials such as grain. It falls to 30% for materials of average flow, and 15% for abrasive or sluggish ones such as cement, ash or sand. A lower loading reduces the wear, the power and the risk of packing at the hanger bearings. The default of 30% suits most of the materials that are carried in industrial and farm conveyors.

How is the power estimated?

The power is the work done to push the mass flow along the trough against the friction of the material and of the screw: P = mass flow × length × friction factor × g / efficiency. The friction factor depends on the material and goes from about 1 for light grain to more than 4 for abrasive, heavy material. This is the horizontal case. Select the motor with a margin of 25% or more for starting the loaded screw.

What limits the speed of a screw conveyor?

The speed is limited by the tip speed and by the fall of the material back on the flights. A fast screw throws the material, wears out the trough and damages fragile products such as grain, so large screws turn slowly: a 9 in screw usually runs below 120 rpm for light materials and near 40 rpm for heavy or abrasive ones. The calculator warns when the tip speed is above 400 ft/min.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.