Skip to content
Omnikalc

Irregular area from offsets: trapezoidal and Simpson’s rule

Enter the spacing and 7 equally spaced offsets from a baseline to get the area of an irregular lot by the trapezoidal rule and by Simpson’s rule, and the difference between them.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Area by Simpson’s rule

3,906.7 ft²

Area by the trapezoidal rule
3,780.0 ft²
Difference, trapezoidal to Simpson
-3.24 %
Area by Simpson’s rule in acres
0.0897 acres

The irregular area calculator gives the area between a straight baseline and an uneven boundary from 7 equally spaced offsets, with the trapezoidal rule and Simpson’s rule, and shows the difference between them.

How the calculation works

  • Enter the distance between the offsets, which must be equal.
  • Enter the 7 offsets measured at right angles from the baseline to the boundary, from the first to the last.
  • The calculator gives the area by the trapezoidal rule and by Simpson’s rule, the difference and the area in acres.

Example

A lot is measured with 7 offsets every 25 ft from a baseline: 0, 18.5, 31.2, 40.6, 36.8, 24.1 and 0 ft. The trapezoidal rule gives 25 × ((0 + 0) / 2 + 151.2) = 3,780 ft². Simpson’s rule gives 25 / 3 × (4 × 83.2 + 2 × 68) = 3,906.7 ft², which is 0.0897 acre. The trapezoidal result is 3.24 % lower, because the boundary is curved.

Why it matters

The calculator helps surveyors, contractors, landscapers, farmers and students to find the area of a lot, a pond, a field or an excavation with a curved side, from a few measurements that can be taken with a tape and a square.

Good to know

Lay out the baseline in a straight line and measure the offsets at right angles, at equal intervals, with the first and last at the ends of the area. If the boundary is smooth, Simpson’s rule is the better value. If the boundary is made of straight lines with corners, put an offset at each corner and use the trapezoidal rule. Use a smaller interval where the boundary bends sharply. The accuracy is limited by the accuracy of the offsets, so measure each one carefully and keep the tape level, then check the area against a second method if the value is important.

The polygon area calculator uses the coordinates of the corners, the average end area calculator gives volumes from sections, the trapezoid calculator gives the area of one trapezoid and the traverse closure calculator checks a boundary survey.

Frequently asked questions

What are offsets?

An offset is the distance, measured at right angles, from a straight baseline to the boundary of an irregular shape such as a lot with a curved side, a pond or a stream bank. When the offsets are taken at equal intervals along the baseline, the area between the baseline and the boundary can be found with a simple rule.

What is the difference between the two rules?

The trapezoidal rule replaces the boundary with straight segments between the offsets. Simpson’s rule fits a parabola through each set of three offsets, so it is more exact for a curved boundary. It needs an odd number of offsets, which means an even number of equal intervals, and here that number is 7 offsets and 6 intervals.

Which result should I use?

Use Simpson’s rule for a smooth curved boundary, because it is usually closer to the true area. Use the trapezoidal rule when the boundary has corners or is made of straight lines. If the two results differ by more than about 2 %, add more offsets at a smaller interval to see how the area changes.

What does the calculator leave out?

The calculator leaves out the area outside the first and last offsets, a boundary that crosses the baseline, offsets at unequal intervals and the slope of the ground when the distances are measured on a slope. Measure the distances horizontally. Add the end areas by hand if the first and last offsets are not zero.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.