Skip to content
Omnikalc

Traverse closure and compass rule calculator

Enter the length and the azimuth of the four sides to get the sums of the latitudes and departures, the error of closure, the relative precision and the adjusted area.

Updated on
Your inputs
ft

Value out of range

°

Value out of range

ft

Value out of range

°

Value out of range

ft

Value out of range

°

Value out of range

ft

Value out of range

°

Value out of range

Results

Relative precision, 1 in

8,678

Precision of 1 in 5,000: suitable for suburban property
Sum of the latitudes
-0.029 ft
Sum of the departures
-0.165 ft
Linear error of closure
0.168 ft
Perimeter of the traverse
1,458.32 ft
Adjusted area
2.983 acres

The traverse closure calculator gives the sums of the latitudes and departures, the error of closure, the relative precision and the area of a four-sided closed traverse, after the compass rule adjustment.

How the calculation works

  • Enter the length and the azimuth (measured clockwise from north) of each of the four sides of the closed traverse.
  • The calculator finds the latitude (north component) and the departure (east component) of each side.
  • It gives the error of closure, the relative precision, and the area after the compass rule adjustment.

Example

A four-sided traverse has sides of 420.08, 310.10, 418.08 and 310.06 ft at azimuths of 91.1°, 181.5°, 271.1° and 1.1°. The latitudes (L cos Az) sum to -0.029 ft and the departures (L sin Az) to -0.165 ft. The error of closure is √(-0.165² + -0.029²) = 0.168 ft. The perimeter is 1,458.32 ft, so the relative precision is 1 in 1,458.32 / 0.168 = 1 in 8,678. The compass rule corrects each latitude and departure in proportion to the length of the side: the correction is −(error) × L / perimeter. The adjusted area, by the coordinate method, is 2.983 acres.

Why it matters

The calculator helps surveyors, civil engineering students and land developers to check the fieldwork before they leave the site, to see whether a traverse meets the required precision and to get the area of a lot from the adjusted coordinates.

Good to know

Measure the angles and the distances with the same care, because the compass rule assumes that the errors are in proportion to the distance. If the precision is low, look for a blunder: a distance that is off by a round number, a transposed digit or a wrong azimuth quadrant. The direction of the error of closure can point to the side that is wrong. Keep the unadjusted values in your field book.

The differential leveling misclosure calculator checks the closure of a level loop, the earth curvature and refraction calculator corrects long sights, the horizontal curve staking calculator sets out the curves of a road and the polygon area calculator gives the area from the coordinates.

Frequently asked questions

What is the closure of a traverse?

A closed traverse returns to its starting point. In theory, the sum of the latitudes (the north-south components) and the sum of the departures (the east-west components) are both zero. Because of the errors of measurement, they are not, and the linear error of closure is the distance by which the traverse fails to close: √((ΣDep)² + (ΣLat)²).

What is the relative precision?

The relative precision is the error of closure divided by the perimeter, written as a ratio 1 in N, with N = perimeter / error. A higher N is better. The usual minimums are 1 in 10,000 for urban boundary surveys, 1 in 5,000 for suburban ones, 1 in 3,000 for rural land and 1 in 1,000 for rough work, but the local law may set its own.

How does the compass rule work?

The compass rule (Bowditch) spreads the error in proportion to the length of the sides. The correction to the latitude of a side is −ΣLat × L / perimeter, and the correction to its departure is −ΣDep × L / perimeter. The adjusted values add up to zero, so the traverse closes, and the area can be found from the adjusted coordinates.

What does the calculator leave out?

The calculator handles four sides, which suits a lot or a small tract. It does not adjust the angles before the sides, and it does not use the transit rule or a least squares adjustment, which are better when the angles are more precise than the distances. For a traverse with more sides, use survey software.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.