Skip to content
Omnikalc

Electrical box fill calculator: does everything fit in the box?

Enter the box volume, the wire size and the number of conductors, devices, grounds and clamps to get the volume required, the percent filled and the room left.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Results

Volume required

18.00 in³

Box fill

89%

Room to spare
Box volume
20.3 in³
More conductors of this size that fit
1

A box that is too full is a fire and shock risk, because the wires cannot dissipate heat and are pushed against the devices. The code limits what goes into a box, and the rule is simple arithmetic. This electrical box fill calculator takes the box volume, the wire size, the number of conductors, devices, grounds and clamps to give the volume required, the percentage of fill and the number of extra conductors that still fit.

How the calculation works

  • Volume allowance per conductor depends on the wire size: 2.00 in³ for 14 AWG, 2.25 in³ for 12 AWG, 2.50 in³ for 10 AWG, 3.00 in³ for 8 AWG and 5.00 in³ for 6 AWG.
  • Count of allowances = conductors + 2 for each switch or receptacle + 1 if there are any grounding conductors + 1 if there are any internal cable clamps.
  • Volume required = count × the allowance of the wire size. Under the code (NEC 314.16), the box volume marked on the box must be at least this value.
  • Box fill = volume required ÷ box volume × 100. Spare conductors = remaining volume ÷ the allowance.

Example

A box marked 20.3 in³ holds 5 insulated 12 AWG conductors, 1 receptacle and the grounding wires, with no internal clamps. The count is 5 + 2 + 1 = 8 allowances. The volume required is 8 × 2.25 = 18.0 in³, which is 89% of the box. It has room for 1 more 12 AWG conductor.

Why it matters

Electricians do this calculation when they add a switch or a receptacle to an existing box, replace a switch by a dimmer, which is larger, or choose a box size for a new circuit. Homeowners who take out an outlet that has wires going on to other rooms often find that the box is already full. The calculation avoids a failed inspection and a hot box.

Good to know

This is a guide based on the main rules of NEC 314.16 for boxes that hold wires of one size, and it does not cover every case. Fittings such as luminaire studs and hickeys, wires of 6 AWG and above in special boxes, and boxes with a lot of devices have extra rules. Some boxes are marked with the volume of the box alone, and extension rings or covers can add to it. Always read the volume printed in the box, and ask the inspector in your area, since local codes can add rules.

The wire size calculator chooses the gauge for a circuit, the wire ampacity calculator gives the current limit of a wire and the electrical outlets calculator estimates how many receptacles a room needs.

Frequently asked questions

How do you calculate box fill?

Count one allowance for each insulated conductor that enters the box, two for each switch or receptacle, one for all the grounding wires together and one for all the internal clamps together. Multiply the count by the volume of the wire size. The result must not be more than the volume marked on the box.

Which conductors are not counted?

A wire that goes through the box without being cut counts once, but a short jumper that starts and ends inside the box does not count. Pigtails shorter than 6 inches that stay inside the box are also left out.

What if the wires are of different sizes?

Count each group at its own allowance and add them. For the grounds, clamps and devices, the code uses the largest conductor in the box, so enter the largest wire size to be safe.

What if the box is overfilled?

Use a larger or deeper box, an extension ring, or split the connections between two boxes. Cramming wires makes heat build up and can damage the insulation.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.