Skip to content
Omnikalc

LED junction temperature calculator

Enter the forward voltage and current, the ambient temperature and the thermal resistances to get the junction temperature and the margin to the limit.

Updated on
Your inputs
V

Value out of range

mA

Value out of range

°C

Value out of range

K/W

Value out of range

K/W

Value out of range

K/W

Value out of range

%

Value out of range

°C

Value out of range

Results

Junction temperature

61.9 °C

Electrical power
2.17 W
Heat to remove
1.41 W
Total thermal resistance
15.5 K/W
Heat sink temperature
48.5 °C
Margin to the maximum junction temperature
63.1 °C

The LED junction temperature calculator gives the electrical power, the heat to remove, the total thermal resistance, the junction temperature, the heat sink temperature and the margin to the maximum junction temperature.

How the calculation works

  • Enter the forward voltage and the forward current of the LED, and the ambient temperature.
  • Enter the thermal resistances from the junction to the case, of the interface, and from the heat sink to the air, and the radiant efficiency.
  • The calculator multiplies the heat by the total resistance, adds the ambient temperature and compares the result with the limit.

Example

An LED at 3.1 V and 700 mA draws 2.17 W and, with a radiant efficiency of 35 %, dissipates 1.41 W as heat. The thermal chain has 15.5 K/W, so at 40 °C the heat sink reaches 48.5 °C and the junction 61.9 °C, which leaves a margin of 63.1 °C under the limit of 125 °C.

Why it matters

The calculator helps lighting designers, electronics engineers and makers who build LED lamps, grow lights, flashlights and displays, and who need to size a heat sink or check that an LED stays within its limit.

Good to know

The junction temperature cannot be measured directly, so it is calculated from the temperature of the solder point or the case, which you can measure, plus the heat times the junction-to-case resistance. The values of the thermal resistance are on the data sheet and depend on the package. A thin layer of thermal paste or a pad reduces the interface resistance, and a metal-core board spreads the heat. The temperature of a luminaire rises over several minutes, so measure after it has stabilized, in the real enclosure. A closed fixture or a high ambient temperature can double the rise. Reduce the current as the temperature rises, using a driver with thermal foldback to protect the LED.

The heat sink calculator sizes the cooler, the LED resistor calculator sets the current of a simple LED circuit, the LED strip calculator handles the power of a strip and the MOSFET power loss calculator gives the heat of a switch with the same thermal method.

Frequently asked questions

How is the junction temperature of a LED found?

The heat that the LED does not emit as light flows from the junction through the case, the interface and the heat sink to the air. Each stage has a thermal resistance in K/W, and the temperature rise is the heat in watts times the total resistance. The junction temperature is the ambient temperature plus that rise: Tj = Ta + Q × (Rjc + Rint + Rha).

How much of the power becomes heat?

A power LED turns 30 to 50 % of the electrical power into light, and the rest, 50 to 70 %, into heat. The calculator takes the radiant efficiency as an input and sets the heat equal to the electrical power times one minus that efficiency. If you use the full electrical power instead, you get a safe, slightly high estimate.

Why does the junction temperature matter?

A hotter junction lowers the light output, shifts the color and shortens the life. A rise of 20 °C can cost 5 to 10 % of the flux, and the life drops by a factor of two for about every 10 to 15 °C above the rated temperature. Most LEDs are limited to a junction temperature of 125 to 150 °C, and designers aim for 85 to 105 °C.

What if the margin is negative?

A negative margin means that the junction exceeds the limit. Reduce the current, add a larger heat sink or a fan, use a better thermal interface material, or choose an LED with a lower thermal resistance. A fan can halve the resistance from the heat sink to the air. Always verify the real temperature with a thermocouple on the solder point.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.