Skip to content
Omnikalc

How big a rack do you need to store kayaks?

Enter the kayaks, their length, beam and deck height, and how many sit on each level: get the levels, the rack height, the arm length, the spacing between supports and the length of wall or floor the rack takes.

Updated on
Your inputs

Value out of range

ft

Value out of range

in

Value out of range

in

Value out of range

Results

Levels

2

Rack height (lowest arm 12 in up)

52 in

Space between levels
20 in
Arm length
30 in
Spacing between the two supports (1/3 of the length)
48 in
Length taken (boat + 1 ft at each end)
14.0 ft
Support plastic kayaks at about a third of their length from each end on padded arms, hull down or on edge, so the hull does not dent; store them out of direct sun and anchor tall racks to the wall

A kayak left on the ground or leaning against a wall takes over the garage and can dent or warp over a season. A rack keeps the boats off the floor, supports them where the hull is strongest, and stacks them so several fit in the footprint of one. This calculator sizes a simple arm rack, either freestanding and double-sided or fixed to a wall.

How the calculation works

  • Levels = kayaks ÷ kayaks per level, rounded up
  • Space between levels = kayak deck height + 6 in, so you can slide a boat in and out
  • Rack height = 12 in for the lowest arm + levels × space between levels
  • Arm length = kayak beam + 2 in
  • Spacing between the two supports = one third of the kayak length
  • Length taken = kayak length + 1 ft at each end

Four 12 ft kayaks, 28 in wide and 14 in deep, stored two per level on a double-sided rack need 2 levels set 20 in apart. The rack stands about 52 in tall, with 30 in arms on uprights 48 in apart, and takes about 14 ft of floor or wall length.

Rack types

Type Kayaks Best for
Wall arms, one side 1 per level narrow garages, 2 to 3 boats
Freestanding, double-sided 2 per level sheds, yards, 4 to 8 boats
Ceiling hoist 1 per hoist high ceilings, rarely used boats
Vertical rack 1 per slot, on end short recreational kayaks

Building and storing tips

  • Supports at the thirds. Placing the two arms about a third of the length in from each end spreads the load, which matters most for plastic hulls that soften in heat.
  • Pad the arms with pool noodles, carpet or foam pipe insulation, and store boats hull down or on their side, never resting on the cockpit rim.
  • Bolt uprights to wall studs or brace a freestanding rack so it cannot tip when you load the top level; keep the heaviest boats low.
  • Keep them out of the sun. UV fades and weakens plastic and composite hulls; use a shed, a covered spot or a breathable cover.
  • Lumber: 4 × 4 posts with 2 × 4 or 2 × 6 arms are enough for most recreational kayaks, which weigh 35 to 60 lb.
  • Leave a few feet of clear space at one end to slide boats in and out, and drain the hull before storing it.

Frequently asked questions

How far apart should kayak rack arms be?

About a third of the kayak's length, so 48 in apart for a 12 ft kayak.

How much space between kayak rack levels?

The kayak's deck height plus about 6 in, so 20 in for a 14 in deep kayak.

How tall is a rack for 4 kayaks?

About 52 in for 2 levels of 2 kayaks, with the lowest arm 12 in off the ground.

Should kayaks be stored on their side or hull down?

Either works on padded supports at the thirds; never rest a kayak on its cockpit rim or leave it in direct sun.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.