Skip to content
Omnikalc

Lewis gear tooth stress calculator: bending stress at the root of a spur gear tooth

Enter the teeth, the diametral pitch, the face width, the power and the speed of a spur gear to get the tangential tooth load, the Lewis form factor, the bending stress and the safety factor against bending.

Updated on
Your inputs

Value out of range

teeth/in

Value out of range

in

Value out of range

hp

Value out of range

rpm

Value out of range

psi

Value out of range

Results

Bending stress at the tooth root

9,415 psi

Tangential tooth load
288.1 lb
Pitch line velocity
1,145 ft/min
Lewis form factor Y
0.319
Velocity factor Kv
0.512
Safety factor against bending
2.12
Adequate safety factor in bending

The Lewis gear tooth stress calculator gives the tangential load, the pitch line velocity, the Lewis form factor, the bending stress at the root and the safety factor of a spur gear tooth from the number of teeth, the pitch, the face width, the power and the speed.

How the calculation works

  • Enter the number of teeth, the diametral pitch and the face width of the gear.
  • Enter the power transmitted, the speed of the gear and the allowable bending stress of its material.
  • The calculator finds the pitch line velocity and the tangential load W = 33,000 hp / V, and the Lewis form factor Y for the number of teeth (20° full-depth teeth).
  • It gives the bending stress σ = W P / (F Y Kv), with Kv = 1,200 / (1,200 + V) for cut gears, and the safety factor.

Example

A gear with 20 teeth and a diametral pitch of 8 (pitch diameter 2.5 in) transmits 10 hp at 1,750 rpm, with a face width of 1.5 in. The pitch line velocity is 1,145 ft/min, so the tangential load is 33,000 × 10 / 1,145 = 288.1 lb. The form factor is Y = 0.319 and Kv = 0.512. The bending stress is 288.1 × 8 / (1.5 × 0.319 × 0.512) = 9,415 psi. For an allowable stress of 20,000 psi, the safety factor is 2.12.

Why it matters

The calculator helps mechanical designers, maintenance engineers, hobbyists and students to size a spur gear, to check a gear that has broken teeth, and to compare materials, face widths and pitches. The Lewis check is the fastest way to get the right order of magnitude of the bending strength of a gear.

Good to know

Use the number of teeth of the weaker gear, usually the pinion. Compare the stress with the allowable bending stress of the material, which depends on the heat treatment. Always check the surface durability too. Use a service factor on the power for shocks, and an AGMA or ISO calculation for the final design of important gears.

The spur gear calculator gives the geometry, the gear ratio calculator gives the speed ratio, the horsepower and torque calculator converts the power and the stress concentration factor calculator covers the effect of the fillet at the root.

Frequently asked questions

What is the Lewis equation?

The Lewis equation, from 1892, treats a gear tooth as a cantilever beam loaded at its tip by the tangential force. It gives the bending stress at the root as σ = W P / (F Y), where W is the tangential load, P the diametral pitch, F the face width and Y the Lewis form factor, which depends on the number of teeth and the tooth shape. It is still the basis of the modern AGMA and ISO bending formulas.

What is the Lewis form factor Y?

Y is a dimensionless number that describes the strength of the tooth shape. It rises with the number of teeth because the tooth gets wider at the root: for 20° full-depth teeth, Y is about 0.245 for 12 teeth, 0.32 for 20 teeth, 0.41 for 50 teeth and 0.485 for a rack. The calculator uses a curve fit of the Lewis table, accurate to about 2% for 12 to 300 teeth.

What does the velocity factor do?

At high pitch line velocity, the impact of the teeth entering the mesh increases the real load above the transmitted load. The Barth factor Kv = 1,200 / (1,200 + V) for cut gears (V in ft/min), or 6.1 / (6.1 + V) in m/s, reduces the allowable load to account for this. For precision hobbed or ground gears, a more favorable factor can be used, such as Kv = 1,200 / (1,200 + V) replaced by an AGMA quality factor.

Is the Lewis equation enough for a gear design?

No. It only checks bending of the tooth. A complete design also checks the surface durability, which is often the limit, with the Hertz contact stress, as well as the dynamic factor of the real quality, the load distribution factor and the overload factor of AGMA 2001 or ISO 6336. Use it for a first sizing, for the choice of the module and the face width, and to compare materials.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.