Skip to content
Omnikalc

Stress concentration factor (Kt) calculator for a flat plate with a hole: nominal stress, maximum stress and safety factor

Enter the width, the hole diameter, the thickness, the load and the yield strength to get Kt, the maximum stress at the hole, the fatigue factor Kf and the safety factor.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

lbf

Value out of range

ksi

Value out of range

Value out of range

Results

Stress concentration factor Kt (net section)

2.42

Nominal stress at the net section
13.33 ksi
Maximum stress at the hole edge
32.27 ksi
Fatigue stress concentration factor Kf
2.14
Safety factor against yielding at the hole
1.12
Small margin: check the load and the material

A hole or a notch in a loaded part creates a stress concentration, and the stress at the edge is higher than the average stress. The stress concentration factor calculator finds Kt for a flat plate with a central hole in tension, the nominal and maximum stresses, the fatigue factor Kf and the safety factor.

How the calculation works

  • Enter the plate width, the hole diameter and the thickness, in inches.
  • Enter the axial tensile force in pounds-force, the yield strength in ksi and the notch sensitivity of the material for fatigue.
  • The calculator finds the stress concentration factor Kt from the ratio d/w, and the nominal stress in the net section, (w − d) × t.
  • It multiplies them to get the maximum stress at the edge of the hole, the fatigue factor Kf and the safety factor against yielding.

Example

A steel plate 4 in wide and 0.25 in thick has a 1 in hole and carries 10,000 lbf. The ratio d/w is 0.25, so Kt = 2.42. The nominal stress is 10 / (3 × 0.25) = 13.33 ksi and the maximum stress is 2.42 × 13.33 = 32.27 ksi. With a notch sensitivity of 0.8, the fatigue factor Kf is 2.14. For a yield strength of 36 ksi, the safety factor is 1.12.

Why it matters

The calculator helps engineering students, designers and makers to check a bracket, a link, a plate or a strap with a hole, to see how the hole size changes the stress, and to understand why cracks begin at holes. It gives quickly a first estimate before a finite element analysis.

Good to know

The formula is for a plate with one central circular hole under uniform axial tension, with a ratio d/w below about 0.65, and the plate is assumed to be wide and thin enough to stay flat. Several holes, holes near the edge, bending, a pin load and plastic yielding need other charts or a finite element analysis. The safety factor against yielding is conservative, because a ductile material redistributes the stress.

The Hertz contact stress calculator finds the stress at a contact, the principal stress calculator finds the maximum stresses from a stress state, the pressure vessel stress calculator finds the stress in a shell, and the section modulus calculator is used for bending.

Frequently asked questions

What is a stress concentration factor?

A stress concentration factor Kt is the ratio of the highest stress at a hole, notch, fillet or other change of shape to the nominal stress that would exist without the change of shape. A Kt of 2.4 means that the local stress is 2.4 times the average stress in the section. Stress concentrations are the usual places where cracks start, especially under cyclic loads.

What formula does the calculator use for a plate with a hole?

For a flat bar with a central transverse hole under axial tension, the calculator uses the polynomial fit Kt = 3.00 − 3.14(d/w) + 3.667(d/w)² − 1.527(d/w)³, where d is the hole diameter and w the plate width, with the nominal stress based on the net section, (w − d) × t. This is the common fit of the charts of Peterson and it is valid for ratios d/w up to about 0.65.

What are the Kt and Kf factors?

Kt is the theoretical factor computed from the geometry. For fatigue, the real effect of a notch is usually smaller, because the material is not completely sensitive to it, and the factor Kf = 1 + q(Kt − 1) uses the notch sensitivity q, between 0 (no effect) and 1 (full effect). Use Kf for fatigue calculations and Kt for brittle materials under a static load.

How can I reduce a stress concentration?

You can use a larger hole radius, a hole farther from the edges, a smooth transition and fillet radii, additional holes or relief grooves that make the flow of the force smoother, or a thicker section around the hole. Cold working or reinforcing the hole with a bushing can also improve the fatigue life.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.