Skip to content
Omnikalc

O-ring squeeze calculator: compression, stretch and groove fill

Enter the cross-section of the O-ring and the dimensions of the groove to get the squeeze, the stretch of the inside diameter and the groove fill of an O-ring seal.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

Results

Squeeze of the cross-section

23.0%

Good squeeze for a static seal
Stretch of the inside diameter
3.3%
Stretch within the usual limit
Groove fill
75.8%
Enough room for the thermal swelling
Free space in the groove
24.2%

An O-ring seals because its cross-section is squeezed in a groove. The O-ring squeeze calculator gives the squeeze, the stretch of the inside diameter and the groove fill, so you can check that a seal is neither too loose nor too tight.

How the calculation works

  • Enter the cross-section of the O-ring and the depth of the groove (the radial space for the ring) to get the squeeze.
  • Enter the inside diameter of the ring and the diameter of the groove bottom to get the stretch. For a piston seal, the ring is stretched over the groove bottom.
  • Enter the width of the groove to get the volume fill, taking the ring as a circle of the cross-section.
  • Compare the squeeze (15 to 30% for a static seal, 10 to 20% for a dynamic seal), the stretch (below 5%) and the groove fill (below 85%).

Example

An O-ring of 0.139 in cross-section and 1.5 in inside diameter goes in a groove 0.107 in deep and 0.187 in wide, with a groove bottom diameter of 1.55 in. The squeeze is (0.139 − 0.107) / 0.139 = 23.0%, good for a static seal. The stretch is (1.55 − 1.5) / 1.5 = 3.3%. The ring section is 0.01517 in² against 0.02001 in² of groove, so the groove fill is 75.8% and 24.2% is left for the swelling of the rubber.

Why it matters

The calculator helps designers, mechanics, plumbers, makers and students to check a groove or a ring on a drawing, to find the cause of a leak, or to choose between two standard sizes. It gives a fast first check before looking at the tables of the manufacturer.

Good to know

Measure the real dimensions of the groove and the ring, since small differences change the squeeze a lot: 0.003 in on a 0.139 in ring is about 2 points of squeeze. Allow for the swelling of the rubber in the fluid. Lubricate the ring at the assembly and avoid sharp edges that can cut it.

The hydrostatic pressure calculator gives the pressure to seal, the thermal expansion calculator estimates the size change with temperature, the bolt torque calculator sets the tightening of the cover, and the friction loss calculator covers the flow in the pipes.

Frequently asked questions

What is the squeeze of an O-ring?

The squeeze is the compression of the cross-section of the ring, in percent of its free cross-section. It is the difference between the cross-section and the depth of the groove, divided by the cross-section. The squeeze creates the contact pressure that seals at low pressure. For a static seal the squeeze is usually 15 to 30%, and for a dynamic seal 10 to 20%, to limit friction and wear.

Why must the stretch be limited?

When a ring is stretched on a piston or a rod, its cross-section shrinks, which reduces the squeeze and the sealing force. A stretch of 1 to 5% is common, and more than about 5 to 10% is poor practice. The calculator gives the stretch of the inside diameter. For a face or a rod seal, the ring is often compressed in diameter, and a small negative value is fine.

What is the groove fill for?

The rubber is nearly incompressible, but it swells in the fluid and expands with the temperature. The groove must have free space for this volume change, so the fill, the volume of the ring divided by the volume of the groove, should stay below about 85%. A fill above 95% can cause the ring to extrude, to wear or to jam the parts.

Can this replace the design guide of the supplier?

No. It is a geometric check. The hardness of the rubber, the pressure, the temperature, the fluid, the surface finish and the extrusion gap are also needed to choose the ring. For high pressure, use anti-extrusion rings, and for critical seals, follow the standard, such as the AS568 sizes or the ISO 3601, and the tables of the manufacturer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.