Skip to content
Omnikalc

Parallel axis theorem (Steiner) calculator

Enter the section size and the distance between the centroid and the new axis to get the second moment of area, the transfer term and the radius of gyration.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

mm

Value out of range

Results

Moment of inertia about the shifted axis

51,666.7 cm⁴

Area of the section
200.0 cm²
Moment of inertia about the centroid
6,666.7 cm⁴
Transfer term A × d²
45,000.0 cm⁴
Ratio to the centroidal value
7.75
Radius of gyration about the shifted axis
160.7 mm
Share of the moment due to the offset
87.1 %

The parallel axis theorem calculator gives the area, the moment of inertia about the centroid, the transfer term A × d², the moment of inertia about the shifted axis, the ratio to the centroidal value and the radius of gyration of a rectangle or a solid circle.

How the calculation works

  • Choose the shape, then enter the width (or the diameter) and the height of the rectangle.
  • Enter the distance between the centroidal axis and the new, parallel axis.
  • The calculator adds the area times the squared distance to the centroidal moment.

Example

A section of 100 mm and 200 mm has an area of 200.0 cm² and a moment of 6,666.7 cm⁴ about its own centroid. Moved to an axis 150 mm away, the transfer term is 45,000.0 cm⁴ and the moment becomes 51,666.7 cm⁴, 7.75 times the centroidal value, with a radius of gyration of 160.7 mm. The offset supplies 87.1 % of the total.

Why it matters

The calculator helps structural and mechanical engineers, students and fabricators who build up sections from plates, move a section onto a support, or need the stiffness of a part bolted away from the neutral axis.

Good to know

The theorem works only from the centroid, never from one shifted axis to another, so always go through the centroidal value. Use consistent units: the area in mm² and the distance in mm give mm⁴. For a built-up beam, find the common centroid first, then add the transfer terms of each part with the distance to that centroid. The stiffness of a beam depends on I, so a plate placed away from the axis counts far more than the same plate at the center. For a hollow section, subtract the moment of the hole computed with the same axis.

The beam deflection calculator uses the moment of inertia to find the sag, the section modulus calculator gives the bending strength, the shaft torsion calculator handles the polar moment of a shaft and the physical pendulum calculator applies the same theorem to a swinging body.

Frequently asked questions

What does the parallel axis theorem say?

The second moment of area of a section about any axis equals its value about the parallel axis through the centroid plus the area times the square of the distance between the two axes: I = Ic + A × d². It works for areas and, with the mass in place of the area, for the moment of inertia of a rotating body. The centroidal axis always gives the smallest value.

Why does the offset term grow so quickly?

The distance enters squared, so doubling the distance multiplies the transfer term by four. This is why beams are built with material far from the neutral axis, like the flanges of an I-beam: the area times d squared gives most of the stiffness, even when the web is thin.

Can I use it for composite sections?

Yes. For each part, compute its own centroidal moment, move it to the common centroid with the theorem, and add all parts. This calculator handles one part at a time, so run it once per rectangle or circle and add the results, subtracting those of holes.

What is the difference between area and mass moments?

The area moment, in cm⁴ or mm⁴, describes the bending stiffness of a section. The mass moment, in kg·m², describes the resistance of a body to angular acceleration. The theorem has the same form for both, with the area replaced by the mass. This calculator gives the area moment about an axis in the plane of the section.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.