Skip to content
Omnikalc

Pipe expansion loop calculator: thermal growth and loop leg length

Enter the pipe material, the length of the run, the temperature change, the diameter and the allowable stress to get the thermal expansion and the leg length that an expansion loop, an offset or a Z bend needs.

Updated on
Your inputs
ft

Value out of range

°F

Value out of range

in

Value out of range

ksi

Value out of range

Results

Leg length of a guided cantilever

8.64 ft

Thermal expansion of the run
0.780 in
Expansion per 100 ft
0.780 in
Leg length of a guided cantilever
103.7 in

A pipe grows when it gets hot, and it needs room to move. The pipe expansion loop calculator gives the thermal expansion of a run of steel, copper or stainless pipe and the leg length of the loop, the offset or the Z bend that absorbs the movement within an allowable stress.

How the calculation works

  • Select the pipe material: carbon steel, copper or stainless steel. The calculator uses its coefficient of thermal expansion and its modulus of elasticity.
  • Enter the length of the straight run between two anchors, the temperature change from the installation to the operating condition, and the outside diameter of the pipe.
  • Enter the allowable bending stress for the leg of the loop, such as 15 ksi for steel, which is a conservative value for a fatigue-sensitive system.
  • The calculator finds the expansion ΔL = α L ΔT and the leg length of a guided cantilever, L = √(3 E D Δ / S), which is the leg that absorbs the movement in a loop, an offset or a Z bend.

Example

A run of 100 ft of carbon steel pipe of 2.375 in outside diameter (2 in NPS) goes through a temperature change of 100 °F. With α = 6.5 × 10⁻⁶ per °F, the expansion is 6.5e-6 × 1,200 in × 100 = 0.780 in, or 0.78 in per 100 ft. For an allowable stress of 15 ksi and E = 29,000 ksi, the leg length is √(3 × 29,000,000 × 2.375 × 0.78 / 15,000) = 103.7 in, or 8.64 ft.

Why it matters

The calculator helps plumbers, pipefitters, mechanical designers and students to estimate how much a heating, steam or process line moves and how much space a loop needs. It gives a quick check before drawing the layout or ordering an expansion joint.

Good to know

Place the anchors so that the movement goes to the loop, and guide the pipe on both sides of it. Use the full temperature range, including the cold condition. A long leg is better than a short one, so round the result up. For a critical system, have the layout checked by a pipe stress analysis.

The thermal expansion calculator covers solid parts, the pipe flow velocity calculator checks the flow, the pipe volume calculator gives the water content and the hydrostatic pressure calculator gives the static pressure of the line.

Frequently asked questions

Why does a pipe need an expansion loop?

A pipe grows when it gets hot. If it is held between two anchors and cannot move, it develops a large compression force, which can bend the pipe, damage the supports and the equipment, or break a joint. A loop, an offset, a Z bend or an expansion joint gives the pipe a flexible section that absorbs the growth without a high stress.

How is the leg length found?

The method of the guided cantilever treats the leg as a beam with a deflection equal to the movement. The bending stress is then S = 3 E D Δ / L², where E is the modulus of elasticity, D is the pipe diameter, Δ is the movement and L is the leg length. Solving for L gives L = √(3 E D Δ / S). A longer leg lowers the stress. A simple offset or a U loop is designed from this length.

How is the temperature change defined?

Use the difference between the lowest temperature of installation or shutdown and the highest operating temperature, whichever gives the larger movement. For a hot water line, this can be from an installation at 50 °F to an operation at 180 °F. For steam, use the saturation temperature. For an outdoor line, include the cold winter condition too.

What are the limits of this calculator?

It gives the simple, conservative estimate of the guided cantilever for a single plane. It does not include the flexibility factors of the elbows, the friction of the supports, the loads on the equipment, the fatigue cycles or the pressure stress. For high-temperature or critical piping, a stress analysis according to the piping code is needed, and plastic pipes need a different method.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.