Skip to content
Omnikalc

Pipe jacking force calculator: thrust needed to jack a pipe through the ground

Enter the pipe diameter, the drive length, the face pressure, the skin friction and the allowable thrust to get the face force, the friction, the total jacking force, the ratio and the maximum drive length.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

psi

Value out of range

kip

Value out of range

Results

Total jacking force

1,285 kip

Force on the face of the shield
28 kip
Friction force on the pipe
1,257 kip
Ratio to the allowable thrust
0.64
Within the thrust capacity of the pipe
Maximum drive length with this friction
628 ft

The pipe jacking force calculator gives the face force, the friction force, the total jacking force, the ratio to the allowable thrust and the maximum drive length of a jacked pipe, from the pipe diameter, the length of the drive, the face pressure and the skin friction.

How the calculation works

  • Enter the outside diameter of the jacked pipe, the length of the drive and the pressure on the face of the shield.
  • Choose the skin friction that fits the ground and the lubrication, and enter the allowable thrust of the pipe.
  • The calculator finds the force on the face, the friction force, the total jacking force, the ratio to the allowable thrust and the maximum drive length.

Example

A pipe of 60 in (5 ft) is jacked over 400 ft, with a face pressure of 10 psi and a skin friction of 200 psf. The force on the face is π/4 × 5² × 144 × 10 / 1,000 = 28 kip. The friction force is π × 5 × 400 × 200 / 1,000 = 1,257 kip. The total jacking force is 1,285 kip, which is 0.64 of an allowable thrust of 2,000 kip. The maximum drive length with this friction is (2,000 − 28.3) / (π × 5 × 0.2) = 628 ft.

Why it matters

The calculator helps trenchless contractors, sewer and utility engineers, estimators and students to size the jacks and the thrust wall, to decide if an intermediate jacking station is needed, and to compare the effect of the lubrication and of the length of the drive on the force.

Good to know

Use a skin friction based on the ground investigation and on the lubrication plan, and keep a margin of at least 20 % on the allowable thrust. Monitor the jacking force during the drive, because a sudden rise can show a block, an obstruction or a loss of the lubrication. Design the thrust wall and the shaft for the maximum force, and check the alignment often to avoid an overload of the joints.

The thrust block size calculator gives the bearing area of a thrust restraint, the pipe wall thickness calculator checks the pipe, the pipeline coverage calculator checks the depth of cover and the excavation calculator gives the volume of the shaft.

Frequently asked questions

What is pipe jacking?

Pipe jacking is a trenchless method in which pipe sections are pushed one by one from a drive shaft through the ground with hydraulic jacks, while a shield or a microtunneling machine excavates the face. The jacking force must overcome the resistance at the face and the friction along the pipe, which grows with the length of the drive. The method is used for sewers, culverts and utility crossings under roads, rails and rivers.

How is the skin friction chosen?

The skin friction depends on the soil, the overcut around the pipe, the lubrication and the time. With a bentonite lubrication of the annulus, the friction can be as low as 100 psf (5 kPa) in stable ground, and in sand and gravel or when the ground closes on the pipe it can be 400 psf (20 kPa) or more. The friction increases after a stop, and the force to restart can be higher than the force in motion.

What is the allowable thrust of the pipe?

The allowable thrust is limited by the compressive strength of the pipe wall and of the joint packing, reduced for the misalignment at the joints and the angle of the drive. Concrete pipe manufacturers give a table of the allowable jacking force by diameter and class. When the total force is higher, intermediate jacking stations are installed to split the drive into sections.

What are the limits of the calculator?

The calculator uses a constant face pressure and a constant skin friction. It does not include the weight of the pipe in the friction, the curves of the alignment, the face support of an earth pressure balance machine, the obstacles, the stops, the settlement or the thrust of the shaft wall and the thrust block. A complete design follows the standards of the pipe jacking associations and uses the data of the ground investigation.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.