Skip to content
Omnikalc

Band brake force calculator

Enter the drum radius, the wrap angle, the friction coefficient and the torque to get the tight and slack tensions, the lever force and the band pressure.

Updated on
Your inputs
mm

Value out of range

°

Value out of range

Value out of range

N·m

Value out of range

mm

Value out of range

mm

Value out of range

mm

Value out of range

rpm

Value out of range

Results

Force at the end of the lever

26.4 N

Tension ratio e^(μθ)
5.204
Braking force at the drum
1,333 N
Tension of the tight side
1,651 N
Tension of the slack side
317 N
Maximum contact pressure on the band
0.275 MPa
Power absorbed by the brake
6.28 kW

The band brake calculator gives the tension ratio, the braking force, the tight-side and slack-side tensions, the force at the end of the lever, the maximum contact pressure and the power absorbed by a simple band brake.

How the calculation works

  • Enter the drum radius, the wrap angle and the friction coefficient of the lining.
  • Enter the braking torque wanted, the distance from the pivot to the slack end and the lever length.
  • Enter the width of the band and the speed of the drum to get the pressure and the power.

Example

To brake 200 N·m on a drum of 150 mm with a wrap of 270 ° and a friction coefficient of 0.35, the tension ratio is 5.204 and the braking force at the drum is 1,333 N. The tight side carries 1,651 N and the slack side 317 N. The lever needs 26.4 N, the band presses at 0.275 MPa and the brake absorbs 6.28 kW at 300 rpm.

Why it matters

The calculator helps designers of winches, hoists, mini-bikes, machines and exercise equipment who use a band brake, and mechanics who need to check the lever force or the band width of an existing brake.

Good to know

Use a friction coefficient that fits the lining and the temperature: 0.25 to 0.4 for woven linings on iron or steel, less if wet or greasy. Keep the pressure under the limit of the lining, about 0.2 to 0.7 MPa for common linings. A wider band lowers the pressure, and a thin band heats up at the contact, so check the power and the cooling. Remember that the tight-side tension acts on the pivot and the drum bearings. Include a safety factor of 1.5 to 2 on the torque, and test the brake in both directions of rotation.

The capstan friction calculator gives the same rope-and-drum relation, the torque calculator handles the moment of a force, the brake pad life calculator estimates the wear of another type of brake and the horsepower torque calculator links the torque and the power.

Frequently asked questions

How does a band brake work?

A flexible band wraps around a rotating drum and is tightened by a lever. The friction between the band and the drum creates a different tension on each side, T1 on the tight side and T2 on the slack side, with T1 / T2 = e^(μ × θ), where μ is the friction coefficient and θ the wrap angle in radians. The braking force is T1 − T2 and the torque is (T1 − T2) × r.

How is the lever force found?

In a simple band brake, the slack side is fixed to the lever at a distance b from the pivot and the tight side to the pivot itself. The moment on the lever is F × L = T2 × b, so F = T2 × b / L. A long lever and a small b give a large amplification, which is why a light hand force can stop a heavy drum.

Why does the wrap angle matter so much?

The ratio of tensions grows exponentially with the wrap angle. With μ = 0.35, a wrap of 180 degrees gives a ratio of 3.0, a wrap of 270 degrees gives 5.2 and a full turn of 360 degrees gives 9.0. A larger wrap reduces the tension of the slack side needed, and so the force on the lever.

Which direction of rotation is the brake meant for?

The calculator assumes the rotation that makes the tight side the one fixed to the pivot, which is the self-energizing direction. In the opposite direction, the same lever force gives a lower torque, because the roles of the sides are swapped. Check both directions if the drum can reverse.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.