Skip to content
Omnikalc

Powder coating coverage and cost calculator

Enter the area, the film thickness, the powder density, the transfer efficiency and the price to get the powder needed, the coverage and the cost per square metre.

Updated on
Your inputs
m²

Value out of range

µm

Value out of range

g/cm³

Value out of range

%

Value out of range

$/kg

Value out of range

Results

Powder to spray

3.45 kg

Powder in the film
2.24 kg
Theoretical coverage
8.93 m²/kg
Practical coverage
5.80 m²/kg
Cost of the powder
34.46 $
Cost per square metre
1.72 $/m²
Overspray to recover
1.21 kg

The powder coating calculator gives the powder in the film, the powder to spray, the theoretical and practical coverage, the cost and the cost per square metre, and the amount of overspray to recover.

How the calculation works

  • Enter the area to coat and the cured film thickness.
  • Enter the density of the powder and the transfer efficiency of your gun and booth.
  • Enter the price of the powder to get the cost.

Example

To coat 20 m² at 70 µm with a powder of 1.6 g/cm³, the film holds 2.24 kg. With a transfer efficiency of 65 %, you spray 3.45 kg, a practical coverage of 5.80 m²/kg against 8.93 m²/kg in theory. The powder costs 34.46 $, or 1.72 $/m², and 1.21 kg go to overspray.

Why it matters

The calculator helps small coating shops, metal fabricators and hobbyists who powder coat parts, and who need to buy the right amount of powder and to price a job.

Good to know

Measure the area of the real part, with both faces and the edges, and not the box that encloses it. Complex parts with recesses have a lower transfer efficiency than flat panels, 40 to 50 % against 70 %. The film thickness varies with the geometry, so use the target of the thickest area you must reach. Verify the thickness with a gauge on a test part, and adjust the voltage and the flow. Store the powder dry and cool, and do not mix brands. Add 10 to 15 % to the quantity for the changes of color and the cleaning losses, and keep a record of the real consumption to refine the estimate.

The paint coverage calculator gives the same idea for liquid paint, the anodizing thickness calculator handles another surface treatment for aluminium, the epoxy resin calculator estimates a thick polymer film and the oven cooking time calculator is a reminder to check the cure schedule of the oven.

Frequently asked questions

How much powder do I need for a given area?

The mass of the film is the area times the thickness times the density. For 20 m² at 70 µm with a density of 1.6 g/cm³, the film holds 2.24 kg. Divide by the transfer efficiency to get the powder to spray: at 65 %, it is 3.45 kg. Add a few percent for the first spray and the cleaning of the gun.

What is the coverage of a powder coating?

The theoretical coverage is 1 000 / (density × thickness in µm) in m² per kg. At 70 µm and 1.6 g/cm³ it is 8.9 m²/kg, and 5.8 m²/kg at 65 % transfer. Powders with a lower density cover more, and a thicker film covers less in proportion.

What thickness should I apply?

Most polyester and epoxy-polyester powders are applied at 60 to 80 µm for a good appearance and protection. Thin films below 50 µm may show the metal through, and above 120 µm the powder can sag, orange-peel or crack. Check the data sheet of the maker.

Can I recover the overspray?

With a recovery booth, the overspray can be sieved and reused, which lifts the practical efficiency toward 95 %. Use a mix of reclaimed and virgin powder, at most 25 to 30 % of reclaimed, to keep the finish consistent. Keep colors separate and the powder dry.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.