Skip to content
Omnikalc

Aluminium anodizing thickness and time calculator

Enter the current density, the time, the efficiency and the part area to get the oxide thickness, the dimension growth, the time for a target and the current.

Updated on
Your inputs
A/dm²

Value out of range

min

Value out of range

%

Value out of range

dm²

Value out of range

µm

Value out of range

Results

Oxide layer thickness

20.7 µm

Thickness in mils (thousandths of an inch)
0.82 mil
Growth of the part on each face
6.8 µm
Increase of the diameter of a round part
13.7 µm
Time to reach the target thickness
48 min
Current for the area
7.5 A
Charge used
5.00 Ah

The aluminium anodizing calculator gives the oxide layer thickness, the dimension growth of the part on each face and on a diameter, the time for a target thickness, the current for the area and the charge used.

How the calculation works

  • Enter the current density and the anodizing time.
  • Enter the current efficiency of the bath, the area of the parts and the target thickness.
  • The calculator applies Faraday’s law to find the thickness and the time.

Example

At 1.5 A/dm² for 40 min with an efficiency of 85 %, the layer reaches 20.7 µm, or 0.82 mil. The part grows by 6.8 µm on each face, and a round part by 13.7 µm on its diameter. To reach 25 µm, run for 48 min. An area of 5 dm² takes 7.5 A and uses 5.00 Ah.

Why it matters

The calculator helps hobbyists and small workshops that anodize aluminium parts, designers who specify a coating thickness and machinists who must allow for the growth of the layer on a fit.

Good to know

The constant of the calculator suits a sulfuric acid bath at about 20 °C. Control the temperature within 1 °C, keep the aluminium clean and well racked to carry the current, and add a safety margin to the area because the real surface includes holes and threads. Measure the layer on a test piece, and adjust the efficiency to match. For a hard coat, the temperature is close to 0 °C and the density up to 3 A/dm², so use a more suitable efficiency. Seal the layer after dyeing to close the pores. Wear gloves and eye protection when you handle acid, and follow the local rules for the disposal of the bath.

The paint coverage calculator estimates other coatings, the epoxy resin calculator handles a polymer finish, the electroplating calculator applies the same law to metals and the galvanic corrosion calculator shows why a protective layer matters.

Frequently asked questions

How is the thickness of an anodized layer calculated?

The oxide mass follows Faraday’s law: each coulomb forms about 0.176 mg of Al₂O₃ at 100 % efficiency. With a density of 2.6 g/cm³ this gives about 0.41 µm per A/dm² and per minute. At 85 % efficiency, 1.5 A/dm² for 40 minutes forms about 21 µm. A traditional rule gives 720 amp-minutes per square foot for each thousandth of an inch.

Does anodizing change the size of the part?

Yes. About one third of the layer grows outward and two thirds penetrate into the metal. A layer of 21 µm increases each face by about 7 µm, so the diameter of a shaft grows by about 14 µm. For tight tolerances, allow for this growth in the machining, and note that hard anodizing grows a little less.

What are the usual thicknesses?

Decorative sulfuric anodizing (type II) is 5 to 25 µm, hard anodizing (type III) is 25 to 100 µm, and thin chromic or architectural films are 2 to 5 µm and 15 to 25 µm. Thicker layers resist wear and corrosion better but are more brittle and absorb dye more slowly.

What affects the efficiency?

The temperature of the bath, the acid concentration and the alloy change the efficiency. Hard anodizing is done colder, close to 0 °C, and at a higher voltage. Alloys with a lot of copper or silicon form thinner and less regular layers. Measure a test coupon with an eddy-current gauge to calibrate the constant of your bath.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.