Skip to content
Omnikalc

Power screw calculator: torque, efficiency and self-locking

Enter the load, the thread diameter, the lead and the friction coefficients to get the torque to raise and lower the load, the efficiency of the lead screw and whether it is self-locking.

Updated on
Your inputs
lbf

Value out of range

in

Value out of range

in

Value out of range

Value out of range

in

Value out of range

Value out of range

Results

Torque to raise the load

139.9 lbf·in

Torque to lower the load
74.8 lbf·in
Efficiency of the screw
22.7%
Self-locking ratio (μ π dm / lead)
1.47
Self-locking: the load stays in place with no brake

A power screw (lead screw) turns a rotation into a linear force, as in a jack, a press or a vise. The power screw calculator gives the torque to raise and to lower a load, the efficiency of the thread and the collar, and whether the screw is self-locking.

How the calculation works

  • Enter the axial load that the screw raises and the mean diameter of the thread (between the major and the minor diameters).
  • Enter the lead, the travel per turn: it is the pitch for a single-start thread, and the pitch times the number of starts for a multiple-start thread.
  • Enter the friction coefficient of the thread (0.1 to 0.2 for steel on bronze with oil) and the collar diameter and friction if the load rests on a thrust washer or bearing. Enter 0 for a collar with no friction.
  • Read the torque to raise and to lower the load, the efficiency and the self-locking ratio.

Example

A square-thread screw carries 1,000 lbf with a mean diameter of 0.625 in, a lead of 0.2 in and a thread friction of 0.15. The collar has a mean diameter of 1 in and a friction of 0.12. The torque to raise the load is 79.9 lbf·in for the thread plus 60 for the collar, or 139.9 lbf·in. The efficiency is 1,000 × 0.2 / (2π × 139.9) = 22.7%. The self-locking ratio is 0.15 × π × 0.625 / 0.2 = 1.47, above 1, so the screw is self-locking, and the torque to lower is 74.8 lbf·in.

Why it matters

The calculator helps designers, machinists, makers and students to size the motor or the handle of a jack, a clamp or a linear actuator, and to decide whether a brake is needed to hold the load. It also shows how much of the input torque is lost to friction.

Good to know

The friction coefficient is the key input and is uncertain, so compute the torque with a low and a high value. Use the high torque to size the motor and the low value to check the self-locking. Lubricate the thread, use a thrust bearing for large loads, and keep a safety margin for the starting torque.

The bolt torque calculator gives the tightening torque of a fastener, the torque calculator relates force and lever arm, the gear ratio calculator sizes the drive, and the inclined plane calculator explains the friction model of a thread.

Frequently asked questions

How is the torque of a power screw computed?

A thread is an inclined plane wrapped around a cylinder. For a square thread, the torque to raise a load F is T = F × dm / 2 × (l + π μ dm) / (π dm − μ l), where dm is the mean diameter, l the lead and μ the friction coefficient. The friction of the collar adds F × μc × dc / 2. For an Acme or trapezoidal thread, divide μ by the cosine of the half thread angle.

What is a self-locking screw?

A screw is self-locking when the friction is large enough to prevent the load from turning the screw down. In theory, the condition is μ ≥ l / (π dm), that is a self-locking ratio of at least 1. Then the torque to lower the load is positive, and you must turn the screw to lower it. Vibration can still back-drive a screw that is only slightly self-locking.

Why is the efficiency so low?

Most of the energy goes into the sliding friction of the thread and the collar. A self-locking screw always has an efficiency below 50%, which is the price of holding the load with no brake. For better efficiency, use a ball screw (efficiency above 90%), a large lead, good lubrication and a thrust bearing in place of a plain collar.

Does it include starting torque and wear?

No. The values are for steady motion and a constant friction coefficient. Breakaway torque is often 20 to 40% higher than the running torque. Also check the buckling of a long screw in compression, the wear of the nut, the bearing pressure of the thread and the temperature at a high duty cycle.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.