Skip to content
Omnikalc

Drilling torque, power and time calculator

Enter the drill diameter, the feed, the speed, the depth and the material to get the torque, the power, the feed speed and the time to drill the hole.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

rpm

Value out of range

mm

Value out of range

°

Value out of range

Results

Cutting torque

3.75 N·m

Cutting power
0.471 kW
Cutting speed at the edge
37.7 m/min
Feed speed
180 mm/min
Length of the point
3.0 mm
Time to drill the hole
11.0 s
Metal removal rate
14.1 cm³/min

The drilling calculator gives the cutting torque, the cutting power, the cutting speed at the edge, the feed speed, the length of the point, the time to drill the hole and the metal removal rate for a twist drill.

How the calculation works

  • Choose the material and enter the drill diameter and the feed per revolution.
  • Enter the spindle speed, the depth of the hole and the point angle.
  • The calculator uses the specific cutting force of the material to find the torque and the power.

Example

A drill of 10 mm in the chosen material, at 1200 rpm and 0.15 mm per revolution, runs at a cutting speed of 37.7 m/min and advances at 180 mm/min. It needs 3.75 N·m and 0.471 kW. With a point of 3.0 mm, a hole of 30 mm takes 11.0 s, removing 14.1 cm³/min.

Why it matters

The calculator helps machinists, makers, maintenance technicians and students who choose a drill press or a hand drill, set the speed and the feed, or estimate the time for a series of holes.

Good to know

The values of kc are averages, and they rise with a blunt drill, a small feed and a hard alloy. Use the torque and the power as a minimum, and add a margin of 30 to 50 % for the efficiency of the drive. Keep the feed in the range recommended for the diameter, about 0.01 to 0.02 times the diameter for steel. Use coolant for steel, stainless steel and aluminium, and peck drill when the depth exceeds three diameters to clear the chips. Clamp the work piece firmly, since the torque can turn the part and injure the operator.

The cutting speed calculator gives the spindle speed for a cutting speed, the tap drill size calculator chooses the drill before tapping, the bolt circle calculator positions a pattern of holes and the horsepower torque calculator links the power of a motor to its torque.

Frequently asked questions

How is the drilling torque calculated?

The torque follows from the specific cutting force kc of the material: M = kc × f × d² / 8 000, in N·m, with the feed f in mm per revolution and the diameter d in mm. For a 10 mm drill with a feed of 0.15 mm in mild steel (kc = 2 000 N/mm²), the torque is 3.75 N·m. It rises with the square of the diameter and in proportion to the feed.

How do I get the power needed?

The power is the torque times the angular speed: P = M × 2π × n / 60. At 1 200 rpm and 3.75 N·m, it is about 0.47 kW. Choose a drill press or a drill with a motor power above this, adding the losses in the drive, and keep in mind that the torque for the same hole rises when the drill is blunt.

How long does it take to drill a hole?

The time is the depth plus the length of the point divided by the feed speed, which is the feed per revolution times the speed. A hole of 30 mm with a point of 3 mm at 180 mm/min takes about 11 seconds. Add the time to retract for peck drilling of deep holes, above three times the diameter.

Which spindle speed should I use?

Choose the speed from the cutting speed recommended for the material and the tool: 20 to 40 m/min for steel with high-speed steel drills, 60 to 100 m/min for aluminium and 40 to 60 for brass. The speed is n = 1 000 × vc / (π × d). The calculator gives the cutting speed at the edge so that you can compare it with the recommendation.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.