Skip to content
Omnikalc

Lag screw withdrawal capacity calculator: design value per inch, capacity of one screw and of a group

Choose the diameter and the wood species and enter the thread length and the number of screws to get the withdrawal capacity of the lag screws.

Updated on
Your inputs
in

Value out of range

Value out of range

lb

Value out of range

Results

Withdrawal capacity of the group

1,525 lb

Withdrawal design value per inch of thread
305.0 lb/in
Withdrawal capacity of one screw
762 lb
Thread length needed in each screw for the required load
0.98 in
Capacity of the group compared with the required load
254 %
The group carries the required load

The withdrawal capacity of a lag screw is the pull-out force that it can resist in wood. The lag screw withdrawal calculator gives the design value per inch of thread, the capacity of one screw, the capacity of the group, the thread length needed for a given load and the ratio of capacity to load.

How the calculation works

  • Choose the diameter of the lag screw and the wood species, which gives its specific gravity G.
  • Enter the length of thread that is embedded in the main member, not counting the tip, and the number of screws.
  • The calculator applies the withdrawal design value for lag screws in the side grain: W = 1,800 × G^1.5 × D^0.75 pounds per inch of thread penetration.
  • It gives the capacity of one screw, of the group, the thread length needed for a required load, and the ratio of capacity to load.

Example

Take 3/8 in lag screws in Douglas fir-Larch (G = 0.50). The design value is 1,800 × 0.50^1.5 × 0.375^0.75 = 305.0 lb per inch of thread. With 2.5 in of thread, one screw resists 762 lb and 2 screws resist 1,525 lb. For a required load of 600 lb, each screw needs only 0.98 in of thread, so the group has 254 % of the required capacity.

Why it matters

The calculator helps builders, carpenters, makers and students to estimate if a few lag screws can hold a load that pulls them out of a timber, for example a handrail, a hanging shelf, a ledger or a bracket. It shows how the diameter, the thread length and the species change the capacity, and how many screws are needed.

Good to know

The formula is a reference design value for lag screws in the side grain of solid wood with a correctly drilled lead hole. It does not include the adjustment factors, the spacing and edge distance rules, the shear and the combined loads, the strength of the steel and the head, or the end grain. Wet wood, treated wood and other conditions reduce the value. Use the code and an engineer for a real structure.

The bolt torque calculator gives the tightening torque of a bolt, the bolt shear capacity calculator handles the shear of bolts, the wood weight calculator gives the mass of lumber, and the rivet size calculator sizes riveted joints.

Frequently asked questions

What is the withdrawal load of a lag screw?

The withdrawal load is the axial force that pulls the screw straight out of the wood. It depends on the diameter of the screw, the length of thread that is embedded in the wood and the density of the species. A lag screw in a dense wood such as oak resists much more than the same screw in spruce, and a longer thread resists more in proportion to its length.

What is the formula?

For a lag screw in the side grain of wood, the design value of the withdrawal load per inch of thread penetration is W = 1,800 × G^1.5 × D^0.75, where G is the specific gravity of the wood and D the diameter of the shank in inches. The result is multiplied by the thread penetration. The formula comes from the American wood design specification.

Which adjustments apply?

The value is a reference design value. It must be multiplied by adjustment factors for the load duration, the moisture of the wood, the temperature and other conditions such as wet service. Lag screws in the end grain have only 75 % of the side grain value, and some codes forbid relying on them. A properly drilled lead hole is required, with the right size for the root diameter.

Can lag screws be used for a heavy hanging load?

Lag screws in withdrawal are used for ledgers, railings or hangers, but a load that pulls the screw out is a risky situation, since the failure is sudden. Where possible, design the connection so that the screws work in shear, or use through-bolts. For a safety-critical connection such as a deck ledger, follow the code tables and the instructions of an engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.