Skip to content
Omnikalc

Rational method calculator: what is the peak runoff flow from my area?

Choose the surface type, enter the rainfall intensity and the drainage area to get the peak runoff flow in cfs, gallons per minute, cubic metres per second and litres per second.

Updated on
Your inputs

Value out of range

Value out of range

Results

Peak flow

8.82 cfs

Peak flow in gallons per minute
3,960 gpm
Peak flow in cubic metres per second
0.250 m³/s
Peak flow in litres per second
250 L/s

When it rains, the water that runs off a roof, a parking lot or a field must be carried away. The rational method calculator takes a surface type, a rainfall intensity and a drainage area and gives the peak runoff flow in cubic feet per second, gallons per minute, cubic metres per second and litres per second.

How the calculation works

  • Peak flow Q = C × i × A. With the intensity i in inches per hour and the area A in acres, Q comes out in cubic feet per second (cfs), since one acre-inch per hour is almost exactly 1 cfs.
  • Runoff coefficient C is the share of the rainfall that runs off at the peak, from 0.95 for roofs and pavement to 0.15 for woods and farmland.
  • In metric units Q (m³/s) = C × i (mm/h) × A (ha) ÷ 360.
  • Conversions: 1 cfs = 448.8 gallons per minute = 0.02832 m³/s = 28.32 L/s.

Example

For a dense residential area (C = 0.70) of 5 acres with a design rainfall intensity of 2.5 in/h, the peak flow is 0.70 × 2.5 × 5 = 8.8 cfs, which is 3,960 gallons per minute or 250 litres per second. Doubling the paved share of the area would raise C and so the flow in proportion, which is why paving changes the size of drains.

Why it matters

The peak flow is the number used to size gutters, pipes, culverts, channels and pumps for stormwater. The rational method is the most common first estimate for small sites, as it needs only three inputs that are easy to find.

Good to know

The method gives a peak flow only, not a volume or a time profile. It assumes uniform rain and a steady state, and it can be too high for larger areas. Local rules may require a given return period, a minimum time of concentration and safety factors. The design of drainage should be checked by a qualified engineer.

The culvert pipe size calculator sizes a pipe for a given flow and the rain garden calculator sizes a garden that captures runoff.

Frequently asked questions

What is the rational method?

It is a simple formula, Q = C × i × A, that estimates the peak flow of runoff from a small drainage area. It assumes the rainfall intensity is the same over the area and lasts at least as long as the time of concentration. Engineers use it to size storm drains, culverts and gutters.

How do I choose the rainfall intensity?

Take it from an intensity-duration-frequency curve for your location, for a chosen return period such as 10 or 25 years, and a duration equal to the time of concentration. Local authorities publish these curves, and NOAA Atlas 14 gives them for the United States.

Which coefficient should I use?

Use the table or choose from the list: about 0.9 to 0.95 for roofs and pavement, 0.5 to 0.7 for dense residential areas, 0.25 to 0.4 for lawns and 0.1 to 0.2 for woods. For mixed surfaces, take an average of the coefficients weighted by area. Steep slopes and saturated ground use higher values.

How large an area is the method good for?

The rational method is meant for small areas, generally under 200 acres (80 hectares), and often limited to 50 acres. For larger watersheds, the storage in the channels and the variation of rain make it overestimate the peak, and a hydrograph method gives a better result.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.