Skip to content
Omnikalc

Retaining wall stem design calculator: steel per foot at the base of a cantilever stem

Enter the stem height, the backfill, the surcharge, the stem thickness, the cover, the concrete and the bar to get the factored moment, the minimum and required steel, the bar spacing and the shear check.

Updated on
Your inputs
ft

Value out of range

lb/ft³

Value out of range

Value out of range

psf

Value out of range

in

Value out of range

in

Value out of range

Results

Maximum spacing of the bars

6.7 in

Factored moment at the base of the stem
53.2 kip-ft/ft
Minimum steel
0.62 in²/ft
Required steel
0.79 in²/ft
Factored shear over the shear capacity
0.52
The shear is carried by the concrete alone

The retaining wall stem design calculator gives the factored moment, the reinforcement and the bar spacing at the base of the stem of a cantilever wall from its height, the backfill, the surcharge and the thickness, with the shear check.

How the calculation works

  • Enter the height of the stem of the cantilever wall, the unit weight and the coefficient Ka of the backfill, and a surcharge on the backfill if any.
  • Enter the thickness of the stem at its base, the cover, the concrete strength and the area of the bar to be used.
  • The calculator finds the factored moment (load factor 1.6) at the base, the minimum and the required steel for the section of 1 ft, the spacing of the bars and the shear over the capacity of the concrete.

Example

A stem of 16 ft retains soil of 110 lb/ft³ with Ka = 0.33 and a surcharge of 200 psf, with a thickness of 18 in and 2 in of cover (d = 15.5 in). The moment is 0.33 × 110 × 16³ / 6 + 0.33 × 200 × 16² / 2 = 33,229 lb-ft, so the factored moment is 53.2 kip-ft/ft. The required steel is 0.79 in²/ft, above the minimum of 0.62, which is 6.7 in of spacing for No. 6 bars. The factored shear is 9.1 kips against 17.6 kips of capacity, a ratio of 0.52.

Why it matters

The calculator helps structural engineers, designers, contractors and students to size the stem of a cantilever wall in a first design, to choose a thickness and a bar spacing and to see the effect of the height and of a surcharge. It reproduces the usual hand calculation of the flexure of a stem.

Good to know

Compute the pressure with a Ka that corresponds to the real backfill and add the surcharge of the traffic or of a building nearby. Provide drainage behind the wall, because water raises the pressure considerably. Check the stability and the footing separately, and extend the bars into the footing by their development length.

The retaining wall calculator checks the stability of a wall, the Rankine earth pressure calculator gives the lateral pressure, the rebar development length calculator covers the anchorage of the bars and the concrete volume calculator gives the quantity of concrete.

Frequently asked questions

What does the stem of a retaining wall do?

The stem of a cantilever retaining wall is the vertical wall that holds the backfill. It behaves like a cantilever beam fixed at the base, loaded by the lateral earth pressure that increases with the depth, and by the surcharge. The maximum moment and shear are at the base of the stem, so the reinforcement is placed on the face in contact with the soil, and can be reduced toward the top.

How is the moment computed?

The triangular pressure of the soil, Ka γ H, gives a force of Ka γ H² / 2 acting at H/3 from the base, so a moment of Ka γ H³ / 6 per unit length of wall. The uniform surcharge adds a rectangular pressure of Ka q, with a moment of Ka q H² / 2. The factored moment is 1.6 times the sum, as the earth pressure is a lateral load in the load combinations of ACI 318.

How is the steel found?

The calculator solves the strength equation of a rectangular section with a width of 1 ft: Mu = φ As fy (d − a/2), with φ = 0.9. The steel is limited below by the minimum of ACI 318, the greater of 3√f'c / fy and 200 / fy times b d. The spacing is the area of the bar divided by the required steel per foot. In practice, the bars at the top are cut off or the section is reduced.

What are the limits of the calculator?

The calculator designs the section at the base of the stem for the flexure and the shear. It does not check the overall stability of the wall against sliding and overturning, the bearing pressure, the heel and the toe of the footing, the temperature and shrinkage steel, the development of the bars into the footing, or the drainage. A qualified structural engineer must design the wall.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.