Skip to content
Omnikalc

Design response spectrum calculator (ASCE 7)

Enter SDS, SD1, TL and the period of the structure to get the design spectral acceleration, the plateau periods T0 and TS, and the seismic coefficient Cs.

Updated on
Your inputs
g

Value out of range

g

Value out of range

s

Value out of range

s

Value out of range

Value out of range

Value out of range

Results

Spectral acceleration Sa at T

0.750 g

Period T0 (start of the plateau)
0.120 s
Period TS (end of the plateau)
0.600 s
Seismic response coefficient Cs
0.094
Sa to SDS ratio
0.75
The period is on the rising or the descending branch of the spectrum

The design response spectrum calculator gives the spectral acceleration Sa at the period of a structure from the design values SDS and SD1 and the long-period transition TL, as in ASCE 7-22 section 11.4.6, with the periods T0 and TS of the plateau and the seismic response coefficient Cs.

How the calculation works

  • Enter the design spectral accelerations SDS and SD1 of the site, which come from the seismic hazard map and the site class, and the long-period transition period TL.
  • Enter the period T of the structure, the response modification coefficient R and the importance factor Ie of the building.
  • The calculator gives the periods T0 and TS of the plateau, the spectral acceleration Sa(T) of the design spectrum of ASCE 7 section 11.4.6 and the seismic response coefficient Cs.

Example

A site has SDS = 1.0 g, SD1 = 0.6 g and TL = 8 s. The plateau ends at TS = SD1 / SDS = 0.60 s and starts at T0 = 0.2 TS = 0.12 s. A building with a period T = 0.8 s is on the descending branch, where Sa = SD1 / T = 0.6 / 0.8 = 0.75 g. For R = 8 and Ie = 1, the response coefficient is Cs = 0.75 / 8 = 0.0937, which is larger than the minimum 0.044 SDS Ie = 0.044. The ratio Sa / SDS is 0.75, so the building is on the sloping part of the spectrum, with a demand lower than the peak.

Why it matters

The calculator helps structural engineers, students and plan reviewers to build the design spectrum quickly, to see on which branch a building falls, to compare the demand of two periods, for example a braced and a moment frame, and to check a hand calculation of the base shear before the modeling in an analysis program.

Good to know

Take SDS and SD1 from the official hazard tool for the exact address, the risk category and the site class, and update them when the code edition changes. Compare the period of the model with the approximate period Ta and with the upper limit Cu Ta. Remember that a longer period lowers the force on the sloping branch, but raises the drift and the displacement. For long structures, check the period against TL, and for the design drift use the amplified displacement of the structure, not the force. Keep the value of R and Ie that matches the structural system of the table, the risk category of the building and the detailing used, and recompute the spectrum when the site class or the hazard values are updated by a geotechnical report or by a new code edition.

The seismic base shear calculator applies Cs to the weight of the building, the story drift calculator checks the displacement under the lateral forces, the diaphragm shear calculator distributes the forces in the floors and the pushover calculator idealizes the capacity curve of the structure.

Frequently asked questions

What is the design response spectrum of ASCE 7?

It is a plot of the spectral acceleration Sa against the period T of a single-degree-of-freedom structure, built from the two design values SDS and SD1. It rises from 0.4 SDS at T = 0, stays at SDS up to the period TS = SD1 / SDS, falls as SD1 / T up to the long-period transition TL and falls as SD1 TL / T² after it. The engineer uses it for the equivalent lateral force, the modal response spectrum and the response history scaling.

How are SDS and SD1 found?

They are two thirds of the risk-targeted maximum considered earthquake values SMS and SM1, which come from the mapped spectral accelerations Ss and S1 and from the site coefficients Fa and Fv of the site class. The USGS seismic design geodatabase and the ASCE hazard tool give the values for an address, a risk category and a site class. The calculator takes them as inputs and does not compute them from the map.

What is the difference between Sa and Cs?

Sa is the elastic spectral acceleration for a given period, which includes the rise of the spectrum at very short periods. The seismic response coefficient Cs of the equivalent lateral force procedure divides the acceleration at the plateau or on the sloping branch by R / Ie, uses SDS in place of the rising branch, and is never lower than 0.044 SDS Ie or 0.01. The base shear is Cs times the effective seismic weight.

When does the calculator not apply?

The spectrum is the general one of ASCE 7. For sites with S1 of 0.6 g or more the code adds a minimum Cs of 0.5 S1 / (R / Ie), which this calculator does not include. For a site-specific ground motion study, for the Eurocode 8 or other national spectra, and for long-period structures with period above TL, use the proper procedure of the code in force and check the result with a licensed engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.