Skip to content
Omnikalc

Roof snow guard spacing and load calculator

Enter the roof pitch, the snow load, the slope length, the friction, the eave length and the guard spacing to get the sliding force, the rows, the load on a guard and the number of snow guards.

Updated on
Your inputs
psf

Value out of range

ft

Value out of range

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Snow guards required

52

Snow weight per foot of eave
716 lb/ft
Sliding force per foot of eave
256 lb/ft
Rows of snow guards
2
Load on one snow guard
256 lb

The roof snow guard calculator gives the sliding force of the snow, the number of rows, the load on one snow guard and the number of snow guards for a sloped roof, from the roof pitch, the snow load, the length of the slope, the friction of the surface and the spacing of the guards.

How the calculation works

  • Choose the roof pitch and enter the snow load, the length of the slope and the friction of the roof surface.
  • Enter the length of the eave, the spacing of the snow guards and the slope length served by one row.
  • The calculator finds the sliding force, the number of rows, the load on a guard and the number of snow guards.

Example

A roof of 6:12 has a slope of 20 ft and a snow load of 40 psf. The snow weighs 40 × 20 × 0.894 = 716 lb per foot of eave. With a friction coefficient of 0.1, the force that makes it slide is 716 × (0.447 − 0.1 × 0.894) = 256 lb/ft. The slope needs 2 rows, so a guard every 2 ft carries 256 × 2 / 2 = 256 lb. An eave of 50 ft needs 26 guards in each row, that is 52 snow guards.

Why it matters

The calculator helps roofers, metal roof installers, designers, building owners and insurers to estimate the number of snow guards for a roof, to see how the pitch and the snow load change the force, and to compare the load with the rating of the products before they order.

Good to know

Use the roof snow load of the code for your site and add the drift and the sliding snow from higher roofs where they occur. Place the guards over the exterior wall and over the entries, and not on a long overhang. Choose the guards and the fasteners with a rating, in lb per guard, higher than the load found, and keep the spacing under the maximum of the manufacturer for your roof profile.

The snow load calculator gives the load of the snow on a roof, the snow drift leeward load calculator gives the load of a drift, the metal roof panels calculator counts the panels of a roof and the roof truss calculator gives the dimensions of a truss.

Frequently asked questions

What is a snow guard for?

A snow guard, or snow retainer, holds the snow on a sloped roof so that it melts or slides in small pieces and not as a block. Without guards, snow can slide off a metal roof all at once and hurt people, damage cars, gutters, plants and the roof below. They are common on metal roofs, which are slippery, over entrances and walkways.

How is the sliding force found?

The weight of the snow on the slope is the snow load times the length of the slope times the cosine of the angle. The part that acts along the slope is the sine of the angle, and the friction of the roof surface resists part of it. The calculator gives the net force per foot of eave. A slippery roof, a steeper pitch and a heavier snow raise this force.

Why use several rows?

On a long slope, one row at the eave would carry the weight of all the snow. A rule of thumb is one row for each 15 ft of slope length, and the load is shared between the rows. The rows are placed in a staggered pattern, and the first row is usually 12 to 24 in above the eave, over the wall below, and not on the overhang.

What are the limits of the calculator?

The calculator uses the ground snow load that you enter, without drift, sliding from an upper roof or ice. It does not include the capacity of the guards and of their fastening, which comes from the test data of the manufacturer and must be higher than the load found here. Ask the manufacturer for the layout, and check the roof structure under the load of the guards.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.