Skip to content
Omnikalc

Snow drift calculator: leeward drift load on a roof step

Enter the ground snow load, the balanced roof snow load and the length of the upper roof to get the snow density, the drift height and width, the surcharge at the step and the maximum snow load.

Updated on
Your inputs
psf

Value out of range

psf

Value out of range

ft

Value out of range

Results

Maximum snow load at the step

101.1 psf

Snow density
19.2 pcf
Height of the leeward drift
3.81 ft
Width of the drift
15.2 ft
Drift surcharge at the step
73.1 psf

The snow drift calculator gives the snow density, the height and the width of the leeward drift, the surcharge at the step and the maximum snow load on a lower roof next to a higher roof, with the ASCE 7 equations, from the ground snow load and the length of the upper roof.

How the calculation works

  • Enter the ground snow load, the balanced snow load of the flat roof and the length of the upper roof upwind of the step.
  • The calculator finds the snow density, the height and the width of the leeward drift, using the ASCE 7 equation.
  • It then gives the surcharge of the drift at the step and the maximum snow load at the step, which is the balanced load plus the drift.

Example

A low roof is next to a higher roof of 100 ft, with a ground snow load of 40 psf and a balanced load of 28 psf. The snow density is 0.13 × 40 + 14 = 19.2 pcf. The drift height is 0.43 × 100^(1/3) × (40 + 10)^(1/4) − 1.5 = 3.81 ft, and its width is 4 × 3.81 = 15.2 ft. The surcharge at the step is 3.81 × 19.2 = 73.1 psf, so the maximum load is 73.1 + 28 = 101.1 psf.

Why it matters

The calculator helps structural engineers, architects, building owners and students to estimate the drift load next to a parapet or a roof step in a first design, and to see how the length of the upper roof changes the load on the lower roof.

Good to know

Check the lower roof for the drift in every wind direction, and also for the sliding snow and the rain on snow. Include the drift in the load combinations with the dead load, and check the roof framing, the deck and the connections near the step, where the load is the highest.

The roof snow load calculator gives the balanced load, the load combinations calculator combines the loads, the wind load calculator gives the wind pressure and the roof scupper sizing calculator checks the drainage of a roof.

Frequently asked questions

What is a snow drift load?

Wind moves snow from the windward side of a roof to the lee of a higher roof, a parapet or a rooftop unit, where it forms a drift. The drift adds a triangular load to the balanced snow load of the lower roof, with its maximum at the step. Roof failures in snowy winters are often due to drifts, because the local load is much higher than the uniform load assumed in the design.

How is the drift height found?

ASCE 7 gives the height of a leeward drift as hd = 0.43 (lu)^(1/3) (pg + 10)^(1/4) − 1.5 in feet, where lu is the length of the upper roof upwind of the step in feet and pg the ground snow load in psf. The calculator uses the equivalent equation in SI units. The width of the drift is 4 hd when the drift is not higher than the clear height, and the surcharge at the step is the drift height times the snow density.

What is the snow density?

The snow density is γ = 0.13 pg + 14 pcf, but not more than 30 pcf. In SI units, the equation is γ = 0.426 pg + 2.2 kN/m³ with a maximum of 4.7 kN/m³. The density is higher for a heavier ground snow load, because the snow is compacted by its weight. The drift load is the product of its height and this density.

What are the limits of the calculator?

The calculator gives the leeward drift only. It does not include the windward drift, which uses a lower fraction of the length, the drift on a sloped roof, the sliding snow from an upper roof, the rain on snow surcharge, the unbalanced loads of a gable roof or the effect of the clear height. The snow loads must be taken from the building code and the structure designed by a qualified engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.