Skip to content
Omnikalc

Rule of mixtures calculator: stiffness and strength of a fiber composite

Enter the fiber volume fraction and the properties of the fiber and the matrix to get the longitudinal and transverse moduli, the longitudinal tensile strength, the density and the share of the load carried by the fibers.

Updated on
Your inputs
%

Value out of range

Msi

Value out of range

Msi

Value out of range

ksi

Value out of range

ksi

Value out of range

lb/in³

Value out of range

lb/in³

Value out of range

Results

Longitudinal modulus E1 (Voigt)

20.00 Msi

Transverse modulus E2 (Reuss)
1.222 Msi
Longitudinal tensile strength
304.0 ksi
Density of the composite
0.0556 lb/in³
Share of the load carried by the fibers
99.0 %

The rule of mixtures estimates the modulus, the strength and the density of a fiber composite from its fiber and matrix. The rule of mixtures calculator gives the longitudinal and transverse moduli, the longitudinal strength and the share of the load carried by the fibers.

How the calculation works

  • Enter the fiber volume fraction in percent, the modulus of the fiber and of the matrix, and the tensile strength of the fiber.
  • Enter the stress in the matrix at the strain where the fibers break, and the densities of the fiber and the matrix.
  • The calculator applies the rule of mixtures: the longitudinal modulus is the volume-weighted average E1 = Ef Vf + Em Vm (equal strain, Voigt model), and the transverse modulus is the inverse weighted average 1 / E2 = Vf / Ef + Vm / Em (equal stress, Reuss model).
  • It gives the longitudinal strength σ1 = σf Vf + σm Vm, the density of the composite and the share of the load carried by the fibers.

Example

A unidirectional carbon-epoxy ply has 60% fibers by volume, with Ef = 33 Msi, Em = 0.5 Msi, σf = 500 ksi, a matrix stress of 10 ksi at the failure strain of the fibers, and densities of 0.064 and 0.043 lb/in³. The longitudinal modulus is 33 × 0.6 + 0.5 × 0.4 = 20.00 Msi. The transverse modulus is 1 / (0.6 / 33 + 0.4 / 0.5) = 1.222 Msi. The longitudinal strength is 500 × 0.6 + 10 × 0.4 = 304.0 ksi, the density is 0.0556 lb/in³, and the fibers carry 99.0% of the load.

Why it matters

The calculator helps materials and mechanical engineers, designers of composite parts, makers of boats, bikes and drones, and students to estimate the stiffness of a ply before a laminate analysis, to compare fibers such as carbon, glass and aramid, and to see the effect of the fiber fraction. It is the starting point of micromechanics.

Good to know

Use the fiber volume fraction, not the weight fraction. Check the stress in the matrix at the failure strain of the fibers with the stress-strain curve of the resin. Treat the transverse modulus as a rough value, and get test data for design. Do not use the rule for short or random fibers.

The Young’s modulus calculator covers the stiffness of a material, the Poisson’s ratio calculator gives the lateral strain, the true stress and strain calculator converts test data and the density calculator handles the mass.

Frequently asked questions

What is the rule of mixtures?

The rule of mixtures estimates the properties of a composite from those of its constituents and their volume fractions. For a unidirectional fiber composite loaded along the fibers, the fibers and the matrix have the same strain, so the stiffnesses add up in proportion to their volumes. Loaded across the fibers, the two have the same stress, and the compliances add up. The two results are upper and lower bounds for the modulus.

Why is the transverse modulus so low?

Across the fibers, the stress passes through the soft matrix in series with the stiff fibers, so the matrix controls the stiffness. The transverse modulus is only a few times that of the matrix, even at a high fiber content. This is why a unidirectional ply is very anisotropic, and why laminates stack plies at several angles, such as 0, 45, 90 and −45 degrees.

How is the strength estimated?

When the fibers are brittle and their failure strain is lower than that of the matrix, the composite fails when the fibers break. The strength is then σ1 = σf Vf + σm′ (1 − Vf), where σm′ is the stress in the matrix at the failure strain of the fibers. For a high fiber fraction the strength is nearly that of the fibers times their fraction. In practice, defects reduce it below the rule.

What are the limits of the rule?

The rule assumes a perfect bond, aligned continuous fibers, no voids and a uniform distribution. The longitudinal modulus is accurate within a few percent, but the transverse modulus and the shear modulus from the simple rule are too low, and the Halpin-Tsai equations are more realistic. Real parts also depend on the layup, the temperature, the moisture and the fatigue.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.