Skip to content
Omnikalc

True stress and true strain calculator: from engineering values and necking check

Enter the engineering stress and strain of a tensile test to get the true stress, the true strain, the current diameter and the strain at which necking starts for a given strain-hardening exponent.

Updated on
Your inputs
psi

Value out of range

%

Value out of range

in

Value out of range

Value out of range

Results

True stress

67,200 psi

True strain
11.33%
Current diameter (uniform deformation)
0.4725 in
Engineering strain at the start of necking
19.72%
Share of the uniform strain used
63.0%
Uniform deformation: the formulas are valid

The true stress and the true strain take into account the change of the cross-section during a tensile test. The true stress and true strain calculator converts the engineering values into the true values, gives the current diameter and checks if the point is before the necking.

How the calculation works

  • Enter the engineering stress (load divided by the original area) and the engineering strain (elongation divided by the original length) from your tensile test, in percent.
  • Enter the original diameter of the specimen, to get the current diameter if the volume stays constant.
  • Enter the strain-hardening exponent n of the material (about 0.1 to 0.25 for steels, 0.4 or more for annealed copper and brass).
  • The calculator gives the true stress σ = σe (1 + εe), the true strain ε = ln(1 + εe) and checks if the point is before the necking, which starts when the true strain equals n.

Example

A steel specimen of 0.5 in diameter reaches an engineering stress of 60,000 psi at an engineering strain of 12%. The true stress is 60,000 × 1.12 = 67,200 psi. The true strain is ln 1.12 = 11.33%. By constancy of volume, the diameter is 0.5 / √1.12 = 0.4725 in. With n = 0.18, necking starts at a true strain of 18%, an engineering strain of e^0.18 − 1 = 19.72%, so the point has used 63.0% of the uniform strain.

Why it matters

The calculator helps materials and mechanical engineering students, testing technicians and designers to convert the data of a tensile test into the true stress-strain curve, which is needed for forming simulations and plasticity models. It also shows how far the test is from the necking.

Good to know

Use the formulas only up to the maximum load. Beyond it, compute the true values from the diameter of the neck measured during the test. For small strains the engineering and true values are almost equal, so the correction matters mainly for the ductile metals at large strains. Fit the exponent n on the true curve between the yield and the maximum load.

The Young’s modulus calculator gives the elastic part of the curve, the Poisson’s ratio calculator relates the transverse and axial strains, the principal stress calculator handles multiaxial states and the critical crack size calculator covers the fracture.

Frequently asked questions

What is the difference between engineering and true stress?

The engineering stress uses the original area of the specimen, but the area shrinks as the specimen stretches. The true stress uses the current area, so it is higher: σ = σe (1 + εe) as long as the deformation is uniform. The engineering curve falls after the maximum load because of the necking, while the true stress keeps rising up to the fracture, because the material hardens.

How is the true strain defined?

The true strain is the sum of the small strains along the test, ε = ∫ dL / L = ln(L / L0) = ln(1 + εe). It is additive, and equal and opposite in tension and compression for the same stretch ratio, which the engineering strain is not. For small strains below 2%, the two values are almost equal, but at 20% the difference is already 2 points.

What is the strain-hardening exponent?

Many metals follow the power law σ = K εⁿ in the plastic range, where K is the strength coefficient and n the strain-hardening exponent. The Considère criterion shows that necking starts at the maximum load, when the true strain equals n. So a material with a high n, such as annealed copper, stretches a lot before the necking, and one with a low n, such as a cold-worked steel, necks early.

Where do the formulas stop being valid?

The formulas σ = σe (1 + εe) and the constant volume assumption are valid only up to the necking. After it, the strain is concentrated in the neck, and the true stress and strain must be computed from the measured diameter of the neck: σ = F / A and ε = 2 ln(d0 / d). The calculator flags the points that are beyond the necking, and it ignores the elastic volume change.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.