Skip to content
Omnikalc

SCS curve number calculator: how much rain becomes runoff?

Enter the storm rainfall, the curve number and the watershed area to get the direct runoff depth, the share of rain that runs off and the runoff volume.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Results

Direct runoff depth

1.25 in

Share of the rain that runs off
41.7%
High runoff
Runoff volume
45,375 ft³
Potential retention S
2.50 in
Initial abstraction (rain absorbed before runoff)
0.50 in

Not all rain that falls on land runs off: soil, plants and hollows absorb part of it. The SCS curve number calculator takes the storm rainfall, the curve number and the watershed area and gives the direct runoff depth, the share of rain that runs off, the runoff volume, the potential retention and the initial abstraction.

How the calculation works

  • Potential retention S = 1000 ÷ CN − 10, in inches (or 25,400 ÷ CN − 254 in millimetres). A higher curve number means a less permeable surface and a smaller S.
  • Initial abstraction Ia = 0.2 × S. It is the rain that is absorbed or held in hollows before any runoff begins.
  • Direct runoff Q = (P − Ia)² ÷ (P − Ia + S) when the rainfall P is larger than Ia, and 0 otherwise.
  • Runoff volume = Q × watershed area. The share of the rain that runs off is Q ÷ P.

Example

For a storm of 3 inches on a residential watershed with CN = 80, S = 1000 ÷ 80 − 10 = 2.5 in and Ia = 0.5 in. The direct runoff is (3 − 0.5)² ÷ (3 − 0.5 + 2.5) = 1.25 in, or 41.7% of the rain. Over 10 acres this is a volume of about 45,375 ft³, or about 1.04 acre-feet.

Why it matters

The curve number method is the most used way of estimating runoff from rainfall in small watersheds. It supports the design of drainage, stormwater ponds and rain gardens, and it shows how much a change of land cover, such as paving a lot, raises the runoff.

Good to know

The method is empirical and results are rough, especially for CN below 50 or for storms below about an inch. The initial abstraction ratio of 0.2 is a long-standing convention that some regions replace with 0.05. Check local regulations, which may set a design storm and method. A drainage engineer should confirm any design.

The rain garden calculator sizes a garden that captures runoff and the French drain calculator covers the sizing of a drain for wet ground.

Frequently asked questions

What is a curve number?

The curve number, developed by the US Soil Conservation Service (now NRCS), summarizes how much rain a surface sheds. It combines the soil's hydrologic group, the land cover and the soil's wetness before the storm. Values near 100 are impervious surfaces, and values of 30 to 60 are well-drained woods or grass.

What curve number should I use?

Tables in the NRCS Technical Release 55 give a CN for each land use and soil group. Typical values for soil group C are 98 for paved areas, about 83 for residential lots with 1/4 acre, 79 for good pasture and 70 for woods. For mixed areas, take an average weighted by area.

Does the method work for small storms?

The method assumes a storm large enough to exceed the initial abstraction, and it is best for storms of 1 inch (25 mm) or more. For small storms and for very small sites, the result is uncertain, and the method gives zero runoff if the rain does not exceed Ia.

What is the runoff volume used for?

The volume sizes detention ponds, rain gardens, swales and culverts, and it estimates how much water a storm will deliver to a stream or sewer. The peak flow, which sets the size of a pipe, needs an additional method such as the rational method or a unit hydrograph.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.