Skip to content
Omnikalc

Scruton number calculator

Enter the mass per length, the damping ratio, the diameter and the frequency to get the Scruton number and the critical wind speed for vortex shedding.

Updated on
Your inputs
lb/ft

Value out of range

%

Value out of range

ft

Value out of range

Hz

Value out of range

Value out of range

lb/ft³

Value out of range

Value out of range

Results

Scruton number

7.78

Critical wind speed for vortex shedding

39.0 ft/s

Vibration risk class (0 under 5 high, 1 from 5 moderate, 2 from 10 low)
1
Critical wind speed (mph or km/h)
26.6 mph
Damping ratio needed for the target Scruton number
0.64 %
Mass per length needed for the target Scruton number
514 lb/ft

The Scruton number calculator gives the Scruton number, a vibration risk class, the critical wind speed for vortex shedding and the damping ratio or mass per length needed to reach a target value, for a chimney, a mast or any slender cylinder.

How the calculation works

  • Enter the mass per unit length, the damping ratio and the outer diameter.
  • Enter the natural frequency of the mode, the Strouhal number and the air density.
  • Enter a target Scruton number to see the damping or mass required.

Example

A structure of 400 lb/ft with a damping of 0.5 % and a diameter of 6.5 ft has a Scruton number of 7.78, class 1. At 1.2 Hz the critical wind speed is 39.0 ft/s, or 26.6 mph. To reach a Scruton number of 10, it would need a damping of 0.64 % or a mass of 514 lb/ft.

Why it matters

The calculator helps structural and wind engineers, students and designers of steel stacks, light poles, antennas, masts and tubular towers who must decide early whether a slender cylinder needs strakes, a damper or a change of mass before a detailed aeroelastic study.

Good to know

Use the damping ratio of the structure in the mode considered, not the logarithmic decrement, and consistent units: pounds per foot, pounds per cubic foot and feet in the US version, kilograms per meter, kilograms per cubic meter and meters in the metric version. The risk classes are a rough reading, since each standard has its own limits and procedures. Lock-in can also occur at higher modes, with ice or with neighboring structures. A wind tunnel test or the applicable standard should confirm important designs.

The damping ratio calculator explains how damping is measured, the tuned mass damper calculator sizes a damper to add damping, the Reynolds number calculator characterizes the flow around the cylinder and the wind load calculator gives the static wind force.

Frequently asked questions

What is the Scruton number?

It is a dimensionless number that combines the mass per unit length, the structural damping and the size of a cylindrical structure relative to the air. It is Sc = 4π m ζ / (ρ D²). A low value means that the structure is light and weakly damped, so wind-excited vortex shedding can build up large oscillations across the wind.

Which values are acceptable?

Codes and guides give different limits. A common reading is that vortex-induced vibrations are strong under about 5, moderate from 5 to 10 and small above about 10 to 15. Eurocode 1 Annex E and other standards give detailed procedures. Check the standard that applies to your project and country.

How is the critical wind speed found?

Vortex shedding locks onto the natural frequency of the structure when the shedding frequency St × V / D equals that frequency. The critical speed is therefore V = f D / St. A Strouhal number of 0.2 is typical for a circular cylinder over a wide range of Reynolds numbers.

How can the vibration be reduced?

Raise the damping with a tuned mass damper or a hanging chain, add mass, or break the shedding with helical strakes or a shroud. Changing the frequency or the diameter also moves the critical wind speed. The target Scruton number lines of this calculator show how much damping or mass is needed.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.