Skip to content
Omnikalc

Septic drain field trench length calculator

Enter the bedrooms, the design flow and the percolation rate to get the loading rate of the soil, the bottom area, the total trench length, the number of trenches and the footprint of the drain field.

Updated on
Your inputs

Value out of range

gal/day

Value out of range

min/in

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Total length of the trenches

250 ft

Design flow
450 gal/day
Loading rate of the soil
0.6 gal/day/ft²
Bottom area of the trenches
750 ft²
Number of trenches
3
Length of each trench
83.3 ft
Footprint of the field
2,250 ft²

The septic drain field calculator gives the trench length and the number of trenches of a conventional drain field from the design flow and the percolation rate, with the loading rate of the soil, the bottom area and the footprint.

How the calculation works

  • Enter the number of bedrooms, the design flow per bedroom and the percolation rate of the soil in minutes per inch.
  • Enter the width of the trench bottom, the maximum length of a trench and the spacing between trenches.
  • The calculator gives the loading rate of the soil, the bottom area, the total trench length, the number of trenches and the footprint of the field.

Example

A 3 bedroom house has a design flow of 3 × 150 = 450 gal/day. A soil with a percolation rate of 25 min/in has a loading rate of 0.6 gal/day/ft², so the bottom area is 450 / 0.6 = 750 ft². With trenches 3 ft wide, the total length is 250 ft, which is 3 trenches of 83.3 ft at the limit of 100 ft. With a spacing of 9 ft, the field covers 2,250 ft².

Why it matters

The calculator helps homeowners, builders, septic installers and designers to see how large a drain field will be on a lot, to compare soils and to check that the area is available before a purchase or a design.

Good to know

Do the percolation test or a soil evaluation in the place and at the depth of the trenches, in the wettest season if you can, because a slow soil sets the size. A percolation rate slower than the limit of your code, often 60 min/in, rules out a conventional field and calls for another system. Keep the trench bottoms level, protect the area from vehicles and keep a reserve area for a replacement, which most jurisdictions require. A bigger field costs more but gives the soil a longer life, so size it with the table of your jurisdiction and not below it.

The septic tank calculator sizes the tank before the field, the septic system replacement cost calculator prices the whole system, the Darcy’s law calculator gives groundwater flow and the infiltration trench calculator sizes a stormwater trench.

Frequently asked questions

What is the loading rate?

The loading rate, or long-term acceptance rate, is the volume of effluent per day that a square foot of the soil can absorb without clogging. It falls as the soil gets slower, from about 1.2 gal/day/ft² in a fast sand to 0.4 or less in a tight silt or clay. The calculator takes the common steps of the percolation test, and your local table governs.

What is the design flow?

The design flow of a house is usually set by the number of bedrooms, because the bedrooms predict the number of people. Many codes use 150 gallons per day per bedroom, some 120. It is not the real use of water, it is a design value with a safety margin, and the code of your jurisdiction sets it.

Why split the trench into several lines?

A long single trench is hard to lay out on a lot and loads the soil at one end first. A distribution box splits the flow between several shorter trenches of equal length, usually not more than 100 feet each, and the spacing between them lets the soil beside each trench take its share of the effluent and the oxygen.

What does the calculator leave out?

The calculator leaves out the depth of the trench and the sidewall area that some codes credit, the reduction for a chamber or a gravel-less system, the slope of the lot, the setbacks to wells and property lines, the groundwater and the repair area that most codes require. A site evaluation by a licensed designer and the permit of the health authority decide the design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.