Skip to content
Omnikalc

Snap-fit calculator: strain, maximum deflection and force of a cantilever hook

Enter the dimensions of a cantilever snap-fit beam, the deflection to assemble and the plastic data to get the strain at the root, the maximum deflection and the assembly force.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

%

Value out of range

Results

Strain at the root of the beam

1.20%

Share of the allowable strain used
60.0%
Safe margin on the strain
Maximum deflection allowed
0.067 in
Stiffness of the beam
18.75 lbf/in
Force to deflect the beam
0.75 lbf

A cantilever snap-fit is a plastic beam with a hook that bends during assembly and locks the parts together. The snap-fit calculator gives the strain at the root, the maximum deflection allowed, the stiffness of the beam and the force needed to assemble.

How the calculation works

  • Enter the width, the thickness and the length of the cantilever beam of the snap-fit hook, with a constant cross-section.
  • Enter the deflection that the beam must make so that the parts go together.
  • Enter the flexural modulus and the allowable strain of the plastic, from the data sheet (about 2% for ABS, 3 to 4% for polypropylene, 1% for filled nylon).
  • Read the strain at the root, the share of the allowable strain used, the maximum deflection allowed, the stiffness and the assembly force of the beam.

Example

An ABS beam is 0.25 in wide, 0.05 in thick and 0.5 in long, and it must deflect 0.04 in to snap on. The strain at the root is 1.5 × 0.05 × 0.04 / 0.5² = 1.20%, which is 60% of the allowable strain of 2%, so the margin is safe. The maximum deflection allowed is 0.02 × 0.5² / (1.5 × 0.05) = 0.067 in. The beam has a stiffness of 300,000 × 0.25 × 0.05³ / (4 × 0.5³) = 18.75 lbf/in, so the force to deflect it by 0.04 in is 0.75 lbf.

Why it matters

The calculator helps product designers, makers, 3D printing users and students to size the hooks of a housing, a cover or a clip, to avoid cracks at the root and to estimate how hard the assembly will be. It gives the geometry to try before the first prototype.

Good to know

Keep the strain below the allowable limit with a margin, and use a generous radius at the root of the beam. A longer, thinner beam is better for the strain, while a thicker beam is better for the retention force. For 3D printed parts, print the beam so the layers do not run across the root, since the strength between layers is much lower.

The bolt torque calculator covers screw fasteners, the thermal expansion calculator checks the change of size of a plastic part, the thermal stress calculator finds the stress of a restrained part, and the gear ratio calculator sizes other mechanical parts.

Frequently asked questions

What is a cantilever snap-fit?

A cantilever snap-fit is a plastic beam with a hook at the free end. During assembly, the beam bends until the hook goes past the edge of the mating part, then it springs back and locks. It is the most common snap-fit in plastic parts, found in battery covers, enclosures and clips. The design is driven by the strain at the root of the beam, not by the stress.

How is the strain computed?

For a beam of constant rectangular cross-section, the strain at the root is ε = 1.5 × h × y / L², where h is the thickness, y the deflection at the end and L the length. A long thin beam has a low strain. A tapered beam, thinner at the end, spreads the strain and allows a deflection up to 1.5 to 2 times larger.

What allowable strain should I use?

The allowable strain depends on the plastic and the number of assemblies. Common values for a one-time assembly are about 2% for ABS, 3 to 4% for polypropylene and 6 to 8% for polyethylene, and about 1% for glass-filled materials. For repeated assembly, use about half of these values. Take the figure from the data sheet of the supplier and reduce it for sharp corners.

What are the limits of this calculator?

It assumes a beam of constant section, a linear elastic material and a small deflection. It does not include the stress concentration at the root, the creep over time, the temperature, the weld lines or the friction of the hook. Add a radius of at least 0.5 times the thickness at the root, and test the real parts, including at the extreme temperatures.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.