Skip to content
Omnikalc

Thermal stress calculator for a bar, rail or pipe fixed at both ends: σ = E α ΔT, axial force and expansion

Enter the modulus, the expansion coefficient, the temperature change, the section and the restraint to get the thermal stress, the axial force and the free expansion of a member.

Updated on
Your inputs
ksi

Value out of range

Value out of range

°F

Value out of range

in²

Value out of range

in

Value out of range

%

Value out of range

ksi

Value out of range

Results

Thermal stress

15.08 ksi

Axial force in the restrained member
60.32 kip
Free expansion if the member were unrestrained
0.0624 in
Thermal strain
520 µε
Stress as a share of the yield strength
41.9 %
The thermal stress is moderate compared with the yield strength

A bar, a rail or a pipe that cannot expand freely develops a thermal stress when the temperature changes. The thermal stress calculator gives the stress σ = E × α × ΔT, the axial force, the free expansion and the share of the yield strength used for a restrained member.

How the calculation works

  • Enter the modulus of elasticity and the coefficient of thermal expansion of the material (for steel, about 29,000 ksi and 6.5 × 10⁻⁶ per °F).
  • Enter the temperature change, the cross-section area, the length and the yield strength.
  • Enter the degree of restraint: 100 % for a member held between rigid supports, and less for supports that give.
  • The calculator gives the thermal stress σ = E × α × ΔT × restraint, the axial force, the free expansion and the share of the yield strength that is used.

Example

A steel bar of 4 in² and 120 in is fixed between two rigid walls and heated by 80 °F. The thermal strain is 6.5 × 10⁻⁶ × 80 = 520 µε and the stress is 29,000 × 0.00052 = 15.08 ksi. The axial force is 15.08 × 4 = 60.32 kip. Without the walls, the bar would grow by 0.0624 in. The stress is 41.9 % of the yield strength of 36 ksi.

Why it matters

The calculator helps engineering students, structural and mechanical designers, pipefitters and builders to check if an expansion joint is needed, to estimate the forces on supports and anchors, and to understand why rails buckle in hot weather and why pipes need loops. It gives the order of magnitude quickly.

Good to know

The model is a uniform temperature change in a prismatic member with a linear elastic material and a constant degree of restraint. It does not include temperature gradients, buckling of slender members, changes of the properties with temperature, creep or the stiffness of real supports. Check the results with a detailed analysis for design.

The thermal expansion calculator gives the free change of length, the Young’s modulus calculator relates stress and strain, the principal stress calculator combines stress components, and the Euler buckling calculator checks the compression of slender members.

Frequently asked questions

What is thermal stress?

When a member is heated or cooled and it is not free to expand or contract, stresses appear in it. If the member is fully restrained, the thermal strain α × ΔT that cannot happen freely is converted into an elastic strain, and the stress is E × α × ΔT. It does not depend on the length of the member or on the area of its section, but the force does.

Is the stress compression or tension?

A heated member that is restrained is pushed against its supports and is in compression, and a cooled member is pulled and is in tension. The calculator gives the size of the stress. A long, slender member in compression can buckle before it yields, and the Euler buckling load should then be checked.

What does the degree of restraint mean?

A degree of 100 % means that the supports are perfectly rigid and the member cannot move at all. A lower value represents supports that give, a joint with some play or a member that is only partly held. The stress is proportional to the restraint in the calculator, which is a simple model for a first estimate.

How can thermal stress be avoided?

The usual ways are to provide expansion joints, sliding bearings, loops or bellows in pipes, gaps between rails or between slabs, and a free end on long members. The design must allow the free expansion shown by the calculator, plus a margin, where the movement can be absorbed.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.