Skip to content
Omnikalc

Interference fit calculator: how tight is the press fit?

Enter the shaft and hub sizes, the interference, the material and the friction to get the contact pressure, the hub stress, the press-in force and the torque the joint can carry.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

Results

Contact pressure

10,878 psi

Hoop stress at the bore of the hub
18,130 psi
Safety factor against yield
1.99
Comfortable margin on the hub
Axial press-in force
6,151 lbf
Torque the joint can carry
256 lbf·ft

A press fit holds a gear, a bearing or a wheel on a shaft by squeeze alone. The interference fit calculator takes the shaft diameter, the hub outer diameter, the length of the fit, the interference, the material, the friction coefficient and the yield strength of the hub and gives the contact pressure, the hoop stress at the bore, the safety factor, the press-in force and the torque capacity.

How the calculation works

  • Contact pressure p = E × (δ ÷ d) ÷ 2 × (1 − (d ÷ D)²), for a solid shaft in a hub of the same material, where E is Young’s modulus, δ the diametral interference, d the shaft diameter and D the outer diameter of the hub.
  • Hoop stress at the bore of the hub = p × (D² + d²) ÷ (D² − d²). It is the highest stress in the hub.
  • Safety factor = yield strength of the hub ÷ hoop stress.
  • Press-in force F = μ × p × π × d × L, with μ the friction coefficient and L the length of the fit.
  • Torque capacity T = F × d ÷ 2. It is the torque that the joint can carry before the shaft slips in the hub.

Example

A steel shaft of 1.0 in in a steel hub of 2.0 in outside diameter, 1.5 in long, with 1 mil (0.001 in) of interference. The contact pressure is 200 000 MPa × 0.001 ÷ 2 × 0.75 = 75 MPa, or 10 900 psi. The hoop stress at the bore is 75 × 5 ÷ 3 = 125 MPa (18 100 psi), so a hub of 36 ksi steel has a safety factor of 2.0. With μ = 0.12 the press-in force is 6 150 lbf and the joint carries 256 lbf·ft of torque.

Why it matters

The same numbers tell you whether a joint will carry its torque, how strong the press must be, and whether the hub will stay elastic. A designer can choose an interference without a key, or check that a bearing seat is not overstressed.

Good to know

The equations apply to a solid shaft and a hub of the same material, assume uniform pressure over a smooth fit and remain elastic. Different materials, hollow shafts, surface roughness that flattens in assembly, and temperature change all change the pressure. Use the formula for a first sizing, and use handbook fits and a stress analysis for real machines.

The bolt torque calculator gives the tightening torque of a fastener and the bearing life calculator estimates how long a bearing lasts under a load.

Frequently asked questions

What is an interference fit?

It is a joint in which the shaft is slightly larger than the hole, so it has to be pressed in or fitted after heating the hub or cooling the shaft. The squeeze creates a pressure at the contact surface and the friction holds the parts together with no key, pin or bolt.

How much interference should I use?

Machinery handbooks give limits and fits by the size of the shaft, such as H7 and p6 or s6. Too little gives a joint that slips, and too much can crack the hub or make the parts impossible to separate. As a rough guide, the interference runs between 0.0005 and 0.002 times the shaft diameter for steel on steel.

Why is the press-in force different from the force that holds it?

The coefficient of friction while the shaft slides in is not the same as when it is about to slip under torque. The first is usually a little lower, particularly with oil on the surfaces. Surface finish, taper, speed and the presence of lubricant all change the values.

Can heating or cooling help?

Yes. A steel hub heated by 100 °C grows by about 12 µm per 10 mm of diameter, which is enough to slide it on a shaft with no force. Cooling the shaft with dry ice or liquid nitrogen shrinks it. Once the temperatures equalize the full interference is back.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.