Skip to content
Omnikalc

Sprinkler system demand calculator: water flow and pressure for a fire sprinkler design area

Enter the design density, the design area, the coverage per sprinkler, the K-factor and the hose allowance to get the sprinkler demand, the number of sprinklers, the flow and pressure of a sprinkler and the total demand.

Updated on
Your inputs
gpm/ft²

Value out of range

ft²

Value out of range

ft²

Value out of range

gpm/psi^0.5

Value out of range

Results

Total system demand with the hose allowance

475 gpm

Sprinkler demand (density × area)
225 gpm
Number of sprinklers in the design area
12
Flow of each sprinkler (density × coverage)
19.5 gpm
Pressure at the most demanding sprinkler
12.1 psi
The pressure is above the usual minimum of 7 psi

The sprinkler system demand calculator gives the water flow of a sprinkler design area from the design density, the area of operation, the coverage per sprinkler and the K-factor, with the pressure at a sprinkler and the total demand including the hose stream allowance.

How the calculation works

  • Enter the design density (gpm per ft²) and the design area of operation from the hazard classification of NFPA 13.
  • Enter the coverage area of one sprinkler, which is limited by the hazard (up to 130 ft² for ordinary hazard) and the K-factor of the sprinkler.
  • Choose the hose stream allowance for the hazard.
  • The calculator finds the sprinkler demand (density × area), the number of sprinklers, the flow and pressure at each one, and the total demand with the hose stream.

Example

An ordinary hazard (Group 1) system has a density of 0.15 gpm/ft² over a design area of 1,500 ft², with 130 ft² per sprinkler of K = 5.6 and a hose allowance of 250 gpm. The sprinkler demand is 0.15 × 1,500 = 225 gpm, with 1,500 / 130 → 12 sprinklers. Each one flows 0.15 × 130 = 19.5 gpm, at a pressure of (19.5 / 5.6)² = 12.1 psi. The total demand is 225 + 250 = 475 gpm.

Why it matters

The calculator helps fire protection engineers, sprinkler contractors, building designers and students to estimate the water demand of a sprinkler system for a building, to size the supply, the pump and the tank in a first design and to compare different hazards. It reproduces the first step of a hydraulic calculation.

Good to know

Take the density and the area from NFPA 13 for the exact occupancy classification and the sprinkler type, and remember that the hazard of a storage area can be much higher than the one of the offices. Add the friction losses and the elevation to the pressure. Check the water supply with a flow test. Only a licensed professional can design and certify the sprinkler system.

The friction loss calculator gives the pressure losses in the pipes, the pump power calculator sizes the fire pump, the tank volume calculator sizes the storage and the pipe flow velocity calculator checks the velocities.

Frequently asked questions

What is the density-area method?

The density-area method of NFPA 13 is the main way to design a sprinkler system. The hazard of the occupancy sets a design density, the flow in gpm per ft² of floor that must be discharged, and a design area, the area over which the sprinklers are assumed to open in a fire. The demand of the sprinklers is the density times the area: for example 0.10 over 1,500 ft² for light hazard, 0.15 for ordinary hazard group 1 and 0.20 for group 2.

How is the flow of one sprinkler found?

A sprinkler must discharge at least the density times its coverage area, so a sprinkler covering 130 ft² under a density of 0.15 gpm/ft² discharges 19.5 gpm. The flow of a sprinkler is Q = K √P, so the pressure needed is (Q / K)². With a K-factor of 5.6 this is 12.1 psi. The pressure must be at least 7 psi in most cases, and the actual pressure at the end of the system is found by hydraulic calculation.

What is the hose stream allowance?

The firefighters use hose streams besides the sprinklers, so the water supply must also provide a hose stream allowance. NFPA 13 gives 50 to 100 gpm for light hazard, 100 to 250 gpm for ordinary hazard and 250 to 500 gpm for extra hazard, for a duration of 30 to 120 minutes. The total demand is the sum of the sprinkler demand and the hose allowance, and the supply must deliver it at the required pressure.

What are the limits of the calculator?

The calculator gives the flow at the sprinklers and the pressure at the most demanding one, but not the pressure loss in the pipes, which depends on the layout, and requires a hydraulic calculation with the Hazen-Williams formula. The values of the densities and the coverage depend on the occupancy and the standard. A system must be designed by a qualified fire protection engineer, and approved by the authority having jurisdiction.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.