Skip to content
Omnikalc

Time of concentration calculator: how fast does runoff reach the outlet?

Enter the length and the average slope of the longest flow path to get the time of concentration, the lag time and the average flow velocity with the Kirpich equation.

Updated on
Your inputs

Value out of range

%

Value out of range

Results

Time of concentration

9.8 min

Time of concentration in hours
0.16 h
Lag time (0.6 × tc)
5.9 min
Average flow velocity
2.54 ft/s

Water falling at the far end of a watershed takes time to reach the outlet, and that time sets the duration of the design storm. The time of concentration calculator takes the length of the longest flow path and its average slope and uses the Kirpich equation to give the time of concentration, the lag time and the average flow velocity.

How the calculation works

  • Time of concentration (Kirpich) tc = 0.0195 × L^0.77 × S^−0.385, in minutes, with the length L in metres and the slope S as a fraction (rise over run). The 1,500 ft flow path is 457 m long.
  • Time of concentration in hours = tc ÷ 60.
  • Lag time = 0.6 × tc. It is the delay between the centre of the rainfall and the peak of the runoff, as used in the NRCS unit hydrograph.
  • Average velocity = length ÷ tc. The Kirpich equation was fitted to small agricultural watersheds, with a flow path that is mostly channelised.

Example

For a flow path 1,500 ft (457 m) long with an average slope of 2%, tc = 0.0195 × 457^0.77 × 0.02^−0.385 = 9.8 minutes, or 0.16 hours. The lag time is 5.9 minutes, and the average velocity is 1,500 ft ÷ 590 s = 2.5 ft/s. A storm lasting at least 10 minutes will therefore make the whole area contribute to the peak flow.

Why it matters

The time of concentration is a basic input in stormwater design. It selects the rainfall intensity for the rational method and defines a unit hydrograph, so it affects the size of culverts, drains, ponds and channels.

Good to know

The Kirpich equation is empirical and gives different results from other methods, such as Kerby, Bransby-Williams or the NRCS velocity method. A watershed made of several kinds of surface should be treated by segments. For urban areas, a minimum time of concentration of 5 to 10 minutes is commonly used. The design should be checked by an engineer.

The culvert pipe size calculator sizes a pipe for a design flow and the drain slope calculator gives the fall needed for a drain.

Frequently asked questions

What is the time of concentration?

It is the time that water takes to flow from the most remote point of a watershed to its outlet. After this time, the whole area contributes to the flow at the outlet. It is used to choose the duration of the design rainfall, because the peak runoff from a storm is highest when the storm lasts about as long as tc.

When should I use the Kirpich equation?

It was developed from data for small agricultural watersheds in Tennessee and Pennsylvania, of 1 to 112 acres with well-defined channels. It works for small rural areas with slopes of 3 to 10%. For overland flow on pavement or short grass, other methods such as the NRCS velocity method or the kinematic wave equation are better.

What is lag time?

It is the time from the centre of the rainfall to the peak of the runoff hydrograph. A common rule links it to the time of concentration, with lag about 0.6 times tc. It is used to build a synthetic unit hydrograph for a watershed when there are no flow records.

How does the slope affect the result?

A steeper path means faster flow and a shorter time. The time falls with the slope to the power of 0.385, so doubling the slope cuts the time by about 23%. A longer path raises the time with the power of 0.77, so doubling the length raises it by about 70%.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.